ARB8057CSR (PARB8057CS0) Amana Refrigerator - Instructions

Based on comments I read at this web site, I first ordered the water valve; that did not fix the problem. Replacing the icemaker did fix the problem. It was easy to replace. Contrary to the instructional video, I couldn't simply tilt out the icemaker at the bottom after removing the lower screww; I had to loosed the two top screws as well. The leak was caused the coating on the icemaker being cracked and peeling.

I watched the video which gave me confidence that I could do the repair which I did in very little time. One thing to emphasize though: When you remove the vertical wire connector from the back of the freezer compartment, remember which color wire is on the top. I needed to watch the repair video a second time to be able to make that determination. Probably the repair video should have mentioned keeping track of that connector regarding the re-connection of it because it could also connect when turned 180 degrees.

I watched a youtube video and completed the repair in less than an hour from start to finish and save myself a service charge. It was fairly easy, the only problem was that it was a bottom freezer and getting to the ice maker was harder than if it was a side by side or top freezer.

I have an Amana freeze and I followed the procedure in the video. Which is very good! However on the Amana Model there two slight differences in the procedure that I felt I needed to do. The first one is, the condenser fan bracket is attached to the Freezer chassis with 4 screws, not three. The removal and installation of the back screw by the fan is a bear. I removed the other three and it allowed me to rotate the fan slightly to get more access to the fourth and did same on installation by just starting the 4th screw and then tightening it later. The second issue was my new fan hit the housing when I spun the fan. When I looked at the old one. It had a phenolic washer, between the fan and motor which spaces the fan out about a washer thickness from the motor. When I tried to remove the old one it broke in four pieces due to age. So, I made my own with a washer that I super glued to the motor housing after carefully centering it on and clearing the motor shaft . Seemed to work with out any more noise or balance issues...Thanks, your delivery was blindly fast and video was great!

replaced left side plastic plate.

My husband had to do this before (bad refrigerator design), so he methodically removed the assembly, replaced the part and replaced all pieces.

I used the video on your website. It made me feel very satisfied that I was able to do it myself!

When the new part arrived we snapped on the new one. Just make sure the draw is closed all the way before closing the refrigerator doors, that's is how mine got broke.

I unplugged the fridge. Then I removed the ice bucket. Then I removed the ice maker using a 3/4 socket to separate the connections and then used a small screwdriver to separate whatever connections were left. Then I installed the new ice maker and checked its level. Everything now works fine.

I was quoted by two repair contractors $125.00 & $149.00 for parts and labor. I paid $16.00 for the pantry end cap plus shipping. Followed the online video from JennAir ....and repaired myself in less than 15 minutes

I was so happy to find that i could order the part online and not have to call a repairman and pay for a service call. The prat shipped in one day! It was very easy to install. Only tip i will give is, make sure you put it in the right direction. If placed in wrong the drawers won't open.

turned off freezer unplugged ice maker ,unscrewed 3 screws, removed ice maker,wiring harness and wire that goes up and down to control ice maker. installed all in reverse put back in and turned on waited and waited no ice ,theres a little control valve that let's the water in as well that was shot as well had to go get one at a local shop fairly interchangable just pull the other out and take with you,or just order one with your ice maker if you have the fridge out you might as well change it as it's just as old as the ice maker as well .everything pumping well,like never before, tons of ice all the time also put in filter on the water line as well really good tasteing ice now.

Grind rivet head off , install rivet tap end

I order a bare crisper frame, no glass, no slider controls. The old frame lifted out easily. I did not realize the glass top is not glued in, because food drippings had it somewhat stuck in place. But only somewhat - I almost dropped the glass when I turned the frame over. Once the glass was out, I removed the humidity sliders by gently lifting one end so I could slide them to a place where they lifted off. (Look for the notch-outs.) Then I put the parts in the new frame and put it back in the frig.

The fix was relatively easy but I could not get 2 of the screws removed. They were in very tight and I didn't have the right tools. Also, in the Amana refridgerator, they are in a "difficult to get at" location. I called my plumber friend and he helped me. Once the screws were out, the rest of the job went very smoothly as others have described. We took out the bad icemaker and reconnected the new one to the existing harness. I had ice in an about an hour. Thanks so much, PartSelect. The delivery was quick and the install was as many described on your website. You provide a wonderful service for the "do it yourselfer". Terri