Models > ARB2107AB (PARB2107AB0)

ARB2107AB (PARB2107AB0) Amana Refrigerator - Overview

Get Parts and Repair Help for ARB2107AB

If you know the refrigerator repair part you need, you can browse the list of all parts on the ARB2107AB, or you can search by name or part description. You can also find your part by where it is located on the ARB2107AB by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for ARB2107AB parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$107.31

Ice Maker

This replacement ice maker mechanism does NOT come with a cover, a wire harness, or the mounting hardware. Must be ordered separately.

$30.70

Condenser Fan Motor Kit

This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a blade mounting nut, and a cushion. This part provides forced-air cooling for the condenser coil.

$35.23

Run Capacitor

This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.

$2.70

Screw

This screw is sold individually.

$16.84

Defrost Timer Kit - 120V 60Hz

The timer will shut off the cooling system of the refrigerator and the defrost heater will turn on.

$20.84

Bimetal Defrost Thermostat - 6" Leads

This refrigerator defrost thermostat will cut out at 55 degrees Fahrenheit and kick back in when the temperature drops to 20 degrees Fahrenheit. This thermostat controls the defrost cycle.

$15.79

Water Fill Cup and Bearing

$2.70

Screw

This screw is sold individually.

$36.13

Water Inlet Valve - 120V 60Hz

$19.65

Icemaker Shut-Off Arm

This part signals the icemaker to stop making ice once the bin has reached a desired amount.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Icemaker producing few or no cubes and often leaving "kling-ons" on ice tray

  • Customer: Bernie from Diamond Bar CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 480 of 487 people found this instruction helpful
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.
Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of con... read more

Water overflowed ice maker turnning ice bucket into solid mass of ice

  • Customer: Harry from Grand Ledge MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 194 of 264 people found this instruction helpful
My ice maker has been shedding its non-stick coating for over a year. Within the last month of so, it started pouring water into the ice bucket below, turning it into a solid mass of ice. So I purchased a new ice maker assembly. I encountered two problems not mentioned in the 21 or so do-it-yourselfer repair stories that precede this one. First problem: o... read more

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 83 of 86 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more