Models > AOR27DEW (P1132341N W) > Instructions

AOR27DEW (P1132341N W) Amana Oven - Instructions

All installation instructions for AOR27DEW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the AOR27DEW
16-29 of 29
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Plastic clip caused the rack to arc to the side of the cavity.

  • Customer: John from Marietta GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Pulled out the old clip and pushed in the new one. Only tool was my fingers and took about 20 seconds. This was after the Sear's web page said the part was no longer available and no replacement was listed.

Thanks to partselect.com I saved the microwave for another couple years.

bottom element wouldn't heat

  • Customer: Sherrie from Orange TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Turned off the breaker. Unscrewed the two srews holding the element in the back of the oven. Pulled out old element. removed the clips from the old element, placed them on the new one. Pushed the element into place. replaced the screws. Turned on the breaker. Total time about 5-6 minutes. Wish all reapirs were this simple and easy.

Lower element not heating

  • Customer: Ken from Paradise CA
  • Difficulty: Really easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
I was astounded, I ordered the part on Thursday afternoon and FedEx delivered it on Saturday afternoon. Great overall service.

Bake Element burned out after 24 years of lot's of use

  • Customer: Terry from Sharpsburg GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 0 of 1 people found this instruction helpful
The key was finding the right socket and using my 1/4 inch socet set and rachet. Remove your nuts, pull out disconnect wires, remove old element and put new one in place. One tip is turn on stove light to be able to see well while in oven.

Slow heating oven

  • Customer: Lisa from Knoxville TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
To diagnose the problem I felt of the element a few moments after turning the oven on. It was cold. (rocket science, I know). I ordered the element replacement, which arrived less than 24 hours later. I turned off the power to the oven, unscrewed the old element and pulled. The wires are attached to the element in a way that reminds me of plugging in a USB port. Plugged, screwed back in, powered up and made some banana bread.

burned oven bulb

  • Customer: Ivanka from Atlantra GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 2 people found this instruction helpful
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

needed new oven light assembly/part #PS1864256

  • Customer: Sara from Harwich Port MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 15 of 48 people found this instruction helpful
Removed old assembly, attached wires to new and inserted into space for same. Of course you must turn off the range circuit breaker. The part that took the most time was removing the old assembly. Once that was done, the rest took only a few minutes.

Door gasket gotten hard

  • Customer: Richard from Pocomoke City MD
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 4 people found this instruction helpful
I took oven door apart and replaced old gasket with new one.

Light bulb failure

  • Customer: Grant from Alexandria VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

oven light replacement

  • Customer: martin from portland OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
bought used, oven light was damaged from previous repair attempt, without installation instructions removing the fixture was tricky, had to bend the housing tabs inward w/screwdriver to release fixture (more damage). once out the new fixture went in place quite easily, wires simply hook up, re install back panel, re-connect power, Have a nice Day!

Lower element burned out

  • Customer: Phil from Patterson NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Just like all the others, remove the two philip's head screws, and pull the wires out far enough to remove connectors. Install connectors on new element, push the wires back into the holes, and screw the cover plates from the new element into the back wall of the oven.

replaced oven lightbulb

  • Customer: peggy ann from forest city NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
very easy

Light burned out in upper oven

  • Customer: Shirley from Las Vegas NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Screwed in light bulb and glass protector

Bulb replacement

  • Customer: Judith from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pulled down the wire around the glass cover...released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
All Instructions for the AOR27DEW
16-29 of 29