Models > AOGD2750WW (P1132527NWW) > Instructions

AOGD2750WW (P1132527NWW) Amana Oven - Instructions

All installation instructions for AOGD2750WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the AOGD2750WW
1-15 of 17
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Getting F 1 and 2 error codes and the oven turned itself off.

  • Customer: Suzanne from Acton MA
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 44 of 85 people found this instruction helpful
Really easy but in this model there are 2 versions of the sensor, male and female. The website didn't have any place to see that. So the first sensor that came was male but we needed the other. After calling they sent me a return form and sent the new part (which was actually much cheaper) overnight and it went in very quickly. Would check this out again when anything went wrong. they are great folks to work with.

STOVE WORK BUT YOUR OVEN WON'T GET HOT ?

  • Customer: Brian from Cumming GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 10 people found this instruction helpful
IF YOUR STOVE WORK'S BUT YOUR OVEN WON'T GET HOT IT IS YOUR IGNIGTER THE IGNIGHTER IN PROPER WORKING CONDITION SENDS A SIGNAL TO THE GAS VALVE SAYING LET THE GAS FLOW ITS OK. WHEN THE IGNIGHTER QUITS WORKING IT WON'T LET THE GAS FLOW AND YOUR OVEN WILL NOT GET HOT. IT IS AN EASY FIX. JUST PULL OUT ALL OF INTERIOR PARTS THE RACKS AND THE BOTTOM HEAT SHIELD THE IGNIGHTER THE WHITE STONE LOOKING PART THAT IS SCREWED TO THE BURNER WITH TWO WIRES AND IT REALLY DON'T MATTER WHAT WAY THE WIRES GO BACK ONE OF THE WIRES CONNECTS IN THE BACK SO YOU WILL HAVE TO PULL THE OVEN OUT. NOW YOU HAVE TO CLEAN UNDER IT AND YOUR DONE.

oven would not light

  • Customer: MATTHEW from SAN CLEMENTE CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 7 of 8 people found this instruction helpful
Removed oven door and burner guard. Removed screws holding ignitor bracket and small panel beneath oven door. Disconnected ignitor wires behind panel and pulled out ignitor. Removed old ignitor from bracket and inserted new unit. Fed wires back down thru tubing and screwed in bracket. Connected wires and replaced panel. (Note: old ignitor glowed but would not pass enough current to operate gas valve)

Replacing the bulb in the freezer side

  • Customer: Yafa (and David) from Bothell WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 4 of 5 people found this instruction helpful
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

hard to get old one out

  • Customer: robert from chatham VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 14 of 35 people found this instruction helpful
easy to put in

oven light burnt out

  • Customer: William from Schwenksville PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 7 people found this instruction helpful
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

light bulb went out in my oven

  • Customer: Janet from Ada MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

needed new oven light assembly/part #PS1864256

  • Customer: Sara from Harwich Port MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 15 of 45 people found this instruction helpful
Removed old assembly, attached wires to new and inserted into space for same. Of course you must turn off the range circuit breaker. The part that took the most time was removing the old assembly. Once that was done, the rest took only a few minutes.

burned oven bulb

  • Customer: Ivanka from Atlantra GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 2 people found this instruction helpful
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Oven not heating, F3 trouble code.

  • Customer: Wesley from Norman OK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed back panel, unplugged sensor, removed sensor from inside oven (2 screws), replaced with new part.

Light bulb failure

  • Customer: Grant from Alexandria VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

oven light replacement

  • Customer: martin from portland OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
bought used, oven light was damaged from previous repair attempt, without installation instructions removing the fixture was tricky, had to bend the housing tabs inward w/screwdriver to release fixture (more damage). once out the new fixture went in place quite easily, wires simply hook up, re install back panel, re-connect power, Have a nice Day!

replaced oven lightbulb

  • Customer: peggy ann from forest city NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
very easy

control panel was burnt out

  • Customer: thomas from iron mountain MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Unscrewed the oven from the opening. Removed the metal housing on the oven. Found the control panel. Hard to remove with the type of plastic anchors holding the panel on. Wasn't bad after that. Just had to keep track of the wires as you disconnected them. Reconnect to new board as you disconnect was the simplest. Worked just fine after that. nice new oven again.

Light burned out in upper oven

  • Customer: Shirley from Las Vegas NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Screwed in light bulb and glass protector
All Instructions for the AOGD2750WW
1-15 of 17