Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ALW780QAC (PALW780QAC)

ALW780QAC Amana Washer - Overview

Parts and Repair Help for models starting with ALW780QAC

If you know the washer repair part you need, you can browse the list of all parts for models starting with ALW780QAC, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for ALW780QAC parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Models starting with ALW780QAC

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$10.08

Adjustable Levelling Leg

Sold Individually. This adjustable leveling leg comes with a stop nut.

Drain Pump

This pump is attached to the motor and helps expel water from the washing machine. It is activated after the spin speed is maintained for a specific period of time.

$63.50

Water Inlet Valve Kit

This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount o...

$27.04

Brake Pad Kit

This brake pad kit contains three brake pads and six installation screws. Helps to bring a rotating cycle to a stop.

$54.61

Flex Vane Agitator

This white agitator is used for belt driven washing machines.

$19.05

Standpipe Adapter

This part helps stop the washer from overflowing.

Drive Bell and Seal Kit

This washing machine drive bell and seal kit comes with a seal, a plug, a shoulder screw, a drive bell, and some grease.

$28.58

Friction Ring

Plastic Washer

This washer is located between the brake and transmission drive pulley.

$29.57

Spin Pulley for Transmission Drive

This helps turn the pump and to help make the washer agitate properly. It is generally positioned between the motor and the pump.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Belt wore out

  • Customer: Bruce from Medina, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 163 of 187 people found this instruction helpful
Had to remove pump-not easy. Nothing wrong with pump, but had to trash it to get it off the motor shaft, so I had to replace it, too.

Pop up top of cabinet and remove front panel. (I leaned unit back against a wall to facilitate internal access once panel was removed.)


Remove motor assy - 4 screws & connector.

Remove ... read more

Drive Pump Leaked

  • Customer: Stephen from Laveen, AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 66 of 78 people found this instruction helpful
It took some trial and error but overall not a difficult project. 1. Take the front covers off. 2. Undo the pully spring to loosen belt 3. Remove belt off idler pulley wheel and free up belt from the large wheel. 4. Disconect the wiring harness and the hoses. 5. Undo the motor mounting bolts (4) 6. Take motor out of washer and remove the 3 screw... read more

The spin belt failed due to overloading the washing machine.

  • Customer: Mark from Cheektowaga, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 38 of 41 people found this instruction helpful
Unplugged the washing machine and turned off the water to the machine. Removed the two front covers; unhooked the two front springs; removed the (4) motor mounting bolts; unhooked the two hoses for the water pump; unhooked the wiring harness; removed the belt from the driven pulley; pulled the motor assembly out; removed the (3) screws to separate the water... read more