ALW221RJW Amana Washer - Instructions

just took the front off and then took the old motor off and switched over about 2 parts from the old to the new and then put the new part on and then placed the front back on and it was ready to go

first remove drive belt then then remove dust cover on bottom of shaft take 5/16 nut driver to only 4 of the screws off that hold the brake cover on install 4 5/16 screws 1" long in those 4 spots.reomve rest of screws then slowly reomve back out 1" screws to relve spring pressure from brake pad.install all new parts from partsselect.com then install other part taken off in oreder and make your wife very happy

Removed the screw from the side of the lid of the washer. Took off the old Lid Switch Actuator and screwed in the new one. Took a little elbow grease because the old screw was tight but no longer than 15 minutes tops.

After replacing the tub to pump hose, I adjusted the feet on the washer. Apparently, the main pulley sits so low on these washers that it ground into the floor and stripped out the thrust bearing. I ordered the new thrust bearing clip and put it in the evening I received it. The instructions it came with were very helpful and it was simple to reassemble. Up until the last piece - the retaining clip. The majority of the repair time was spent replacing that clip. If there is a tool that makes the job easier, I didn't have it. I finally got it on with two flathead screwdrivers prying the shaft out while I wedged one corner of the clip in the groove.

I removed the part that was still attached to the washer and installed the new flume. It took less than five minutes and a repair that would have cost over $85 cost less than $10 and I am no plumber!

I didn’t have special tool for brake but punch and hammer worked. Seal was easy to replace. Several videos online to show you how. It wasn’t worth it to tear apart the transmission and buy more parts/seals (if they were even available). But I didn’t know how much oil was in it. I drilled a hole in the side to somewhat check level and added 80-90 gear oil. It was almost empty and added almost a quart. Used a self taping screw/bolt with gasket sealer to plug the hole. I got 34 yrs out of this washer. If it fails, oh well. Just hate to buy a new one that only last 10yrs if im lucky.

Removed damaged pulley installed new pullley and clutch. The directions made it easy. Aligned pulley as detailed and installed new front feet and tested washer. Took me about 30 minutes to repair. Washer has been working since. Thanks guys for a nice no nonsense package.

if you move the agiatater all the way to one side you can acess the star screws from under the hinge then push the agitator to the other side and acess the screw on the other hinge , you dont have to remove the top of the washer, let me say i did not have the serial no and the people at part select were very helpful and pacient when i called and they got me the RIGHT part the firdt time.thanks again for all your help the job came out perfect and saved me a lot of money for a repair man. ASHER

Took out the two top screws out that hold the top down on the back so you can lift the lid up. Removed the cover plate on the back. Take out the screw that holds the valve in place. Reach up through the access panel and undo the to clips that hold the hose and wiring. Lift the lid up and pull the unit up and remove hose and electrical connections and put back in reverse order. Very simple to do.

PROBLEM: The washer lid has two hinge pins that are attached to the lid with Phillips screws (one per pin). The plastic pin that inserts into the hinge broke off, allowing the lid to come free. SOLUTION: First, I removed the lid from the washing machine. Second, I used a Phillips-head screwdriver to remove the original hinge pins from the lid. Third, I replaced the hinge pins. Fourth, I used a flat-head screw driver to pry up the washer top to obtain easier access to the hinge screws. Fifth, I removed the original hinges with a Phillips-head screwdriver (one screw per hinge). Sixth, I attached the new hinges to the washer lid. Finally, I attached the hinges (and lid) to the washer top, then lowered the washer top.

The lid hinges are fastened to the top of the washing machine body, near the edge of the lid, with 1 screw each.
To remove the old lid hinges, with the lid clamped in the open position, I needed to gain access to the screw heads from underneath, just inside the edge of the lid opening. To get at these screw heads, I needed to push the inside wash drum toward the screw I wanted to remove and wedge something in the gap created between the body of the washer opening and the drum, directly opposite the screw that I pushed the drum towards. What? This is to hold the drum completely out of the way while getting at the screw. My wedge was the handle of a squeege that just happenned to be nearby, but just about anything will work.
Once the drum was secure, I was able to get at the screw head, which, by the way, is a totally blind operation; you cannot see the screw head, only feel it. I guess we're kind of used to feeling our way around these days. Anyway, I had to repeat the wedging thing to remove the other lid hinge.
The only real problem I had was the original (factory installed) screw heads were hex heads, and I struggled a bit finding the correct size allen wrench to blindly remove the screws. It is a good thing that I also ordered 2 new screws along with the new lid hinges because the new screws have phillips heads. Much easier to work with, even though they were a little pricey. The old hex head screws were kind of worn and it would have been a cursing operation to try to reuse them.
Once the old hinges were off, I removed the lid, installed the new hinges on the lid and clamped the lid in place in the open position, while I screwed the new hinges on (wedging the drum out of the way like before). NOTE: It might be a good idea to line the wash drum with newspaper in case a screw slips out and finds its way into one the holes in the drum; lost forever. Anyway, this may sound like alot, but it really isn't. My wife didn't even comment on how the lid isn't smashing down on her any more. That's OK, I'm grateful I'm not the one doing laundry!

I opened up the top of the washer which exposed the tub, I took the top ring off the tub and under in side of the ring is the seal. Took the old one out and put the new one in. The old seal was completely wore out.
It was real easy.
Finding the part is usually the hardest part, but thanks to Parts Select finding the part was the easiest part of the repair.

i followed the directions i found online. do not take the screws all the way out! The snubber ring solved the problem. I replaced the springs since i had them. The old ones seemed OK.

Always check the basics first!

Mistakenly replaced the water valve (even though it was buzzing idicating it had power and showed 110V across terminals). Assumed the water lines were working. Turned out to be a clogged cold water line (safety valve clogged). Replaced both lines for good measure, machine working fine.

Pulled wahser away from wall, unpluged, removed screws from rear access panel, removed hoses from water pump, used towell to absorb excess water still in pump and hoses, removed drive belt, removed screws securing pump, removed old pump replaced it with new pump, cussed a little when replacing hoses, repeated steps in reverse order, checked for leaks.