ALW210RMW (PALW210RMW0) Amana Washer - Instructions

pulled cover off face of machine to gain axcess
saw pulley had come off brass sleeve( Bad design should have had a larger washer on bottom to help support pulley ) would of prevented this problem
Removed motor to gain axcess to pulley and belt change . Keep a towel near by to catch any extra water still in hoses on lower pump

I have call the number that is at the washer top they recomended 2 maytag repair places i call the 1st one and 2nd one charge 75 dollars for estimate and 2nd 65.00 i pay 65 dollars for him to come to my house and turn the washer on for 2 sec. and gave me an estimated of 839. w/that money i can buy another washer i call my dad and ask him to help me to pull the washer apart and thats how i find out it need it the pump search the web and find partselect order and i was expecting the part to arrive 5-6 days later and to my surprise i receive the parts next day w/outpaying next day shipping, and start the repair. Remove the screws from the front of the washer to get access to the bottom of the waher where the motor is the pump is located under the motor. remove 1 of the springs the holds the outer tube, remove 4 more screws to pull the motor out, remove the shield motor and pull the pump out replace w/new one and put everythig back together.( recomendation) pay attention to how thing are before you start if possible keep screws and label separate like top screw,middle screws etc....... thank you Lidia

this machine seems good to work on because almost every thing is done from the front without pulling it away from the wall. Removed front lower cover by removing two screws. There are three brake pads with two bolts each. applied silicone grease to each pad and put it back togather

I had to take the entire tub assembly from the machine to replace the milkstool which had been crushed by the weight of over-loading the washer. It took about 2 & 1/2 hours to complete the job, but it was well worth the effort to save the expense of replacing the appliance. Part Select provide the right part as promised and saved me a lot of money. Thank you for your service.

Unplugged washer and disconnected water lines and drain hose from wall. Removed the two Screws at bottom front panel and tilted lower portion out at bottom and removed panel. Removed screw on each side under to top panel, removed three phillps screws on top control box to tilt the top box forward and unplugged the wiring harness,unscrewed the ground wire, pulled off water level hose, disconnected switch power wire connections. Slid control forward and removed. Found broken spring and anchor slit rusted thru where spring attached to base. Cut a 1/2" strip of metal from a 2x4 metal strap and attached to bottom side of base with screws, set washer uprite and tilted top panel to attach springs to tub. Inserted spring at bottom and pulled spring into slit on side of tub with a heavy gauge bent wire, bent like the top of springs being replaced. Reconnecd wiring to to panel box & Hose, srewed in place at top, reattached screws uhder top front left and right and inserted front panel at top and attached two front screws at bottom. Reattached hoses and plugged in unit. checked for spin, o.k.

I tipped the tub towards the area where the springs were and connected them. They broke because that particulary area seemed to get moisture and they rusted. Truthfully, although the machine still works, its last days are just down the road.

Ipulled the front panel off and found that the brake pads had broken into pieces, ordered new pads. Two of the pads were accessed from the front of the machine and were relatively easy to replace by removing the two attaching bolts, spreading gap in area that they fit into with a plastic pry tool. I gained access to the third pad by removing the punch-outs on the side of the machine (circular). If I had not had these prepuched pieces available to me I would have simply cut an access hole in the rear of the machine with a jig saw, (who will ever see it).

Remove the lower access door in the front of the machine. Then I tipped the washer back against the wall to access everything. The pads are alittle hard to push in between the washer pulley disc. So I first pushed in an old broken brake pad off to the side, then was able to push in the new pads. The rear pad is the hardest and I had to release some of the front tub springs and remove the pump hose for access. Overall it went pretty smooth. Thanks for your help!Tim

I unplug the power plug, turned off water supply and unsrewed the water lines connected to the clogged valve.I unsrewed six screws on the front of the washing machine and took the front panals off. lifted the the washing top and replace the hose and intake valve, which was shipped to me. put the top down and put the two front panals. reconnected the water supply to the new valve and turned the water back on. connected the electric plug.works as good as new.

I disconnected the water supply line to washer and moved washer into open area. I removed the front panel of washer to gain access to drain hose. I removed hose and reinstalled new hose. I did turn the hose holder inside the washer as it allowed the old hose to rub against the housing support of the washer causing the hose to leak. I was glad that I read the article that someone mentioned in their repair. The new hose was somewhat difficult to maneuver through the back of the washer and through the part that held the hose; otherwise, it was rather easy. Thanks for the feed back on your web page.

I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, roller, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.

Removed the damaged legs, replaced with parts from this site and leveled the washer .

Part received was correct (5 days ARO). Removed motor assy from unit (left wires connected). Found drive belt was also worn out & obtained a new one locally. Seperated old pump from rusted motor shaft using 2 screwdrivers. Had to use a file to lightly "polish" rust off motor shaft to install new pump. On-line parts diagram helpful in getting belt properly alinged to idler pully. Machine now runs smoothly, dosn't leak and sound like new. Wife happy (me too)!

First removed all screws with a nutdriver then lifted the body from the base. Removed the two hoses at the pump (be ready for excess water). Removed the 9/16 bolts (4) to drop the motor assy. I also took off the two front balance springs to have easy access. I at this point was able to remove the pulley and put new belt & pump on the motor. Remember to watch carefully to align belt. removing the idler pulley is a no brainer. Took about 45mins. to complete, a no pro job!!

Very easy repair. Removed the lower front panel of the washing machine (two screws) with nutdriver.

Removed hose clamp with pliers. Removed hose from machine. Replaced hose and ran thru a full cycle to check for leaks.

No leaks, back in business in under an hour. This time includes going out to garage and gather the two tools needed for the job and cleaning up the water that came out of the hose during the removal process.