ALW210RAW Amana Washer - Instructions

Had to remove pump-not easy. Nothing wrong with pump, but had to trash it to get it off the motor shaft, so I had to replace it, too.

Pop up top of cabinet and remove front panel. (I leaned unit back against a wall to facilitate internal access once panel was removed.)


Remove motor assy - 4 screws & connector.

Remove 3 pump screws (torx) and 2 hoses. Pry pump off motor shaft (not easy). I used a heat gun to help expand the plastic fitting on the motor shaft.

Remove old belt, put on new belt. (Do not use automotive belt-this belt is designed to slip because it also spins the tub. The tub will not spin when it's full of water, and the pump will not pump the water if the tub is bogging down the pump. Plus, you will probably overheat the motor.)

Press new pump back on motor shaft (advise not to re-use old pump as seals were probably damaged by removal process.)

Caution: Pressing pump onto motor shaft may cause pump rotor to bind in housing. Try to press it on a little too far so you back off slightly.

Replace pump screws.

Replace motor, giving attention to belt alignment.

Replace motor screws and connector.

Re-attach hoses on pump.

Button up cabinet.

Done.

The hardest part was removing the pump. If not for that, it would have been a 15-min, $20 repair.

Because I felt it wise to replace the pump also, it was a $70 repair.

Spin cycle sounded like freight train, bad bearing, apparently they all fail the same way, this revised parts kit should prevent premature failure in future.

The following is easy for an experienced mechanic of any type, fully doable by an accomplished DYI'er, between this writeup and the kit instructions (which I do not fully follow) you should be fine. Probably avoid this task if you aren't either of the aforementioned.

Remove lower pannel, top pannel, lift top back. Remove fill hose to outer tub, clear tube to outer tub. Remove entire outer cabinet from base, exposing base and tub. Remove augur assy by popping off cap removing inner bolt, lifting augur out. Remove top of outer tub cap assy by pressing down where each latch is and gently prying latch open with screwdriver. Remove bolts holding in inner tub and remove inner tub. Unscrew the pastic nut on transmission shaft using channel locks (counterclockwise from top), don't worry about destroying this part since a new one is in the kit. Remove (pry off with your hands, don't worry about breaking it) the 'lint filter' (looks like a frisbee) and trash it. Remove the large (about 8")aluminum hub (that the inner tub bolts to) by unscrewing counterclockwise. No special tool needed, just use air hammer if available against one of the T shaped castings to get it loose, otherwise use a drift and hammer same way. Don't worry about messing up the part since a new one is in the kit. Remove the outer tub drain hose, remove six screws holding outer tub, lift outer tub out. Turn outer tub upside down and use a wide crowbar/nail puller to CAREFULLY pry out the bearing/seal assy from the bottom of the tub. Take your time working your way completely around the bearing/seal several times so it doesn't get too crooked while removing it. Clean everything thoroughly. Inspect the area of the bottom of outer tub where you removed the bearing/seal. If all is well and there are no gouges, get it wet with clean water and then carefully press the new bearing/seal assy in with the heal of the palm of your hand, working your way around it so it doesn't get crooked while pressing in. Do not use sealer (unless there are gouges) and do not hammer this. Make sure it is fully seated in the outer tub. Do reverse to put everything back together. I tightened the aluminum hub the same way I loosened it, no problem. There are some rubber plugs in the kit to install in some holes in the tub, scrape or clean any gunk off the inner tub around these holes so the rubber plugs will seat properly. Carefully snug the plastic nut with channelocks by gripping it from the top as opposed to the side (so the fins don't break). Note there is a small o-ring on the transmission shaft to change before replacing the augur. Nice and quiet after the repair, hopefully the new kit (and trashing the 'lint filter') makes it last longer... LOL, it's a bit disturbing seeing the gunk under the augur knowing that has been there all this time while 'cleaning' the laundry! I'll probably start removing the augur every so often to clean under there.

It took some trial and error but overall not a difficult project. 1. Take the front covers off. 2. Undo the pully spring to loosen belt 3. Remove belt off idler pulley wheel and free up belt from the large wheel. 4. Disconect the wiring harness and the hoses. 5. Undo the motor mounting bolts (4) 6. Take motor out of washer and remove the 3 screws holding the pump to the motor. 7. The pump had melted to the shaft and required I chisel the pump off of the shaft. 8. Attach new pump paying attention to where the belt is positioned. 9. Reattach the motor bolts, hoses, and wiring harnes. 10. Attach the belt and test the pump. 11. Put the front back on.

Water was leaking on the floor during the wash cycle and especially during draining of the washer. I removed the front panel at ground level and watched while draining after a rinse.

I t was obvious that water was spraying from a hole in the rubber end of the hose (the hose is a fused assembly of a plastic section and a rubber section).

So, I finished draining, removed the hose (required pliers to squeeze off a hose clamp).

Upon inspecting the hose, it was also apparent that the hole was caused by rubbing against a support bracket for the motor. This should not happen, but it did because the plastic standoff supposed to keep the hose away from the bracket was installed 180 degrees backwards.

So, I simply replaced the hose and turned the bracket around to the correct orientation.

Everything worked as planned and my repair cost was much less than if I had called someone out.

Unplugged the washing machine and turned off the water to the machine. Removed the two front covers; unhooked the two front springs; removed the (4) motor mounting bolts; unhooked the two hoses for the water pump; unhooked the wiring harness; removed the belt from the driven pulley; pulled the motor assembly out; removed the (3) screws to separate the water pump from the motor; removed the belt from the motor pulley; installed new belt and repeated above in reverse to put everything back together; started washing machine and it worked great.

First removed the front panels and tilted the top back.Disconnected the electrical connector to the motor,removed the cabinet base screws and slid the entire cabinet away from the interior after disconnecting the clear tube and the water feed to the panel.removed bolt inside agitator and remove agitator.removed the plastic hold down center nut with channel lock pliers.remove top cover from outer tub(pry out over tabs with screw driver).remove 4 bolts holding inner tub and remove tub.remove inner bottom tub support with pliers(screws off).remove 6 machine screws from frame to bottom of plastic outer tub and remove tub.Carefully pry seal/bearing out of tub from the bottom(remember its just plastic).install is just the reverse of the dissassembly.Note: This is the second seal/bearing for this washing machine in less than 2 yrs..I work in the Site developement/construction field and my clothes get extremely dirty.The dirt is being held under the inner tub support and driven down thru the seals and into the bearing(great design).This go around the intsructions called for the removal of the plastic lint filter under the tub support which I believe was a large part of the problem.I hope so.I'm not going to spend $90 every 2 yrs. on this machine.Good luck.

firsted layed washer back On A Angle For Easy Acess To Motor Removed Both Hoses And Four bolts pulled Motor Assembly out replced belt @ idler Pulley Reinstalled Motor.

This is not a bad repair, but give yourself some time. I did not have to take the tranny and motor out, but the inner and outer tub and all related parts had to come out, along with the outer tub base. If you are replacing the tub bearing, you HAVE to order the seal kit. Don't try to skimp like I did, since you will need the seal kit as this is what causes that bearing to fail in the first place. We forgot how quiet the washer was after I fixed it, and it saved us from buying a new washer since we were ready to say the heck with it and buy a new pair. You might need an 1.5 inch socket to get the big nut off the spindle, but I was able to get with a visegrip and hammer. The nice thing about this repair is even if you screw it up, you won't have water all over the place because of the seal design. I just checked under the washer a few times for the first few weeks and all seems fine.

I was doing laundry one day, and noticed that the washer did not drain. I drained the water via a shop vac and checked the hoses. There was a baby sock stuck in the hose leading to the pump! I cleared the jam and the washer finally drained again. Once I ran another load, the washer wouldn't drain. I repeated the procedure, and found that the motor was spinning but the pump was not working. I disconnected the machine and proceded to remove the pump. I found that, due to blockage, the motor had reamed out the housing that turns the pump. So, at the advice of my father, who has used this site for other repairs, I entered the model make and number. I was able to view an exploded schematic of the washer in order to correctly identify the part I needed. I found the part, ordered it, and it came to me in about 2 days. I replaced the pump, and my washer has worked great ever since. Thank you PartSelect.com.

All went well 1-remove front panel 2 screws 2-remove 2 front springs tilt tub 3-forward bottom out 4-remove pump 3 torx screws 5-r and r belt pulley and spring reassemble fast service as well thank you

I first unplugged the washer. I removed the 2 screws that hold the front panel and removed the front panel, they are located at the very bottom outer edges of the front panel.
I then removed 4 of the large springs that are attached to the drum, this washer has six but I only removed the front 4. Removed the two hoses going to the water pump and drain hose, removed 4 bolts that attach the motor to its mounting bracket. Unplugged the wiring harnesses going to motor and what looks like a capacitor mounted to the side of the motor.Then I removed the drive belt. ( when the machine would first start to spin it would make a clacking noise which ended up being a chunk out the the drive belt causing the belt tenshioner to slap causing that noise and letting the drum spin during the wash cycle. So far very easy. I then removed the motor and when it is disconnected you can then remove the water pump. Three hex head bolts need to be removed and it pulls right off. I then removed the six bolts that hold the brake pads in place. I applied silicone grease to the new brake pads and installed them. The pad at the back of the drum was very hard to line up with the holes. I used a very small screwdriver to line up the disc brake mounting holes to get the bolts started and it worked fine. I then put it all back together and it works great. I have to add that I have been an auto mechanic for 28 years and not to brag but this is not your average repair job.

to replace the seals is the easier part of the job. I Removed the front panels and removed the front screws for the top and opened up. Then you have to remove the agitator, then the bell plug, the bolt holding the bell along with the bell, then the 1-1/2" nut under that. then slide the plastic washer that fits into the splne. to remove the drum you have to remove the plastic top to the drum assembly. Then you can remove the drum along with the along with the alumunum splined hud that is atrtached the the metal drum. Before removing the drum the seal under the plastic washer mentioned above needs to be removed. once the drum is out you can in bolt the aluminum splined hub from the metal drum. The outer plastic drum has a seal that is glued and slides over the vertical flange. The glue is not included in the kit. once the botom seal is installed. install the new aluminum splined hub to the metal drum. install lower seal to botom of the splined hub. reinstall the hub. once the large nut and plastic spined washer is installed. The top seal neds to tapped onto the hub agian with an object that matches the dia. of the seal flange. the n install the bell, nut ans plug. The bell does not like to align to the splined shaft, do not force it. reinstall the agitor an assemble the rest.

took off 2 bolts
on front panel (at the bottom). removed the spring tentioner.
next i spun the belt around until it came off
the pullies.
Then i removed 4 bolts holding the (pump and motor) spun this around to expose the pump screws(4) Took off the pump and did the same inreverse order except i put a new belt on also...
Good LUCK!!!

Remove the electrical power plug and disconnect the water hoses at the back. Remove the lower front panel by taking out the two screws at the bottom edge. Then lift out the upper front panel which exposes the two sheet metal screws holding down the top panel. Lift open the top panel and secure it up about 90 degrees so it doesn't flop over backwards. Twine tied to something overhead works fine. Replacement procedure for the valve is obvious, once exposed.

Unplugged washer then took back off control panel. Removed clamp and tube from pressure switch. Pushed in tabs with a screwdriver and lifted top. Removed clamp and broken tube. Put new tube in place and tighten clamp with nutdriver. Closed top and put other end of tube on pressure switch with clamp. Put back on control panel and plugged in. Clamps are to big for application but do work. So far so good!