ALG230RCW Amana Dryer - Instructions

1) Removed lower panel
2) Removed door
3) Removed Front Panel - removed connectors from switch and marked connections
4) Removed Front Bulkhead
5) Glides and Felt pads were missing, and brackets were nearly worn through
6) Removed and Replaced old brackets
7) Attached self-adhesive felt pads
8) Attached Drum Glides
9) Removed old felt seal
10) Glued new felt seal in place with 5-min epoxy
11) Allowed Epoxy to set and stop stinking
12) Re-attached front bulkhead
13) Re-attached remaining parts

Dryer works great, is quiet again, and no longer eats clothes!!!!!!

1 Unplug power.
2. Remove the front of the unit by removing the two screws at the bottom of the front panel. Front dryer panel will swing out from the bottom and then the clips will release the top of the panel, careful not to disconnect the dryer door switch. ( can be unplugged to remove the front panel out of the way.)
3. Looking inside the unit on the right side you will see the gas value. On top of the gas unit you will see two small coils the coil closest to the burner has two leads on it. Remove the two screws to get to the coils, remove the medal plate, remove the connector then lift off the secondary coil. Replace and test. You can test unit with the front panel off. (be careful). If no heat, check that the Flat Style igniter is glowing. (ohm out both coils) before ordering parts. Intermittent heat problems. I replaced the secondary coil, it did ohm out o:k but it had swollen and was very tight on the shaft.

This was much easier than I expected. I pulled the front covers, released the belt (just move tentioner pulley with fingers to release belt), removed the drum to access the motor. The motor was easy to remove. I loosened then nut in the fan assy using my channel locks (because I did not have a socket that big and then removed the wire harness clip to prepare the motor for removal. The two mounting clips were the tricky part as the fit over a metal ear on each side locked by the spring tension of the clips. It looks like a special tool my be available but I simply used my big straitslot and heavy downward pressure to remove and install. This repair can be completed by anyone with very basic mechanical skills and impress the spouse.

I changed out the cycling thermostat and the high limit thermostat. Mainly because that was what my research indicated was the problem. I then found some more information online that indicated the gas solenoid valves were bad. I ordered them from you and replaced them. The problem was fixed.

In order to replace the valves you need to remove the top panel. Two screws at the top of the front door assembly hold it on. Remove the screws, lift up on the front panel door assembly and move it to the side. The drum will rest in place. In the lower left corner, under the drum, you will see the solenoids. Two screws attach a plate that holds down the solenoids. Take the hold down plate off, disconnect the control wires attached to the solenoids and lift out the solenoid/control valves. To assemble everything, work backwards to the start. Good Luck

After reading about other people with this same problem I took a chance that this would be what was wrong with my dryer.I took off the front cover of the dryer by removing two screws. I located the faulty coils and simply plugged in the 2 new coils Tah-dah Probably coud have been done without even removing the front panel, but since it was off I vacuumed out the lint ( actually my husband did all of the above, but I tell a better tale than he does and I diagnosed the problem and ordered theparts)

First unplugged unit .2nd took off front cover and removed bottom screws and that allows it to open up and lean back.3rd pryed the motor lock down springs by applying pressure down and out . forth used vise grips to hold motor shaft, while using the 7/8 socket to loosen the blower fan.Last go through steps to put back together.

Removed front of gas dryer and cleaned all lint out. Checked HSI, and cleaned flame sensor. Split (3 terminal) gas coil terminals were intermittent. Read about 700 ohms across outer two terminals, but center terminal to either outer terminal was open (Infiniti on meter) 2 terminal coil measured about 550 ohms. 3 terminal coil should read about 700 ohms across outer terminals, and about 1.5K ohms center to outer terminals. Unscrewed index cover plate and replaced coil, 2 terminal coil was okay. Reassembled and finished 12 loads of laundry no problems at all.

I ordered a new lint filter from PartSelect. The part was in stock, and it was delivered to my home in approximately 40 hours -- yes, a little more than a day and a half! To do the repair, I removed the old lint filter and put the new one in its place.

Unplug the power cord from the unit. Remove the lower front panel; then the upper front panel including the door (unplug wire to door switch). Then remove the cover on the fan housing. Need to block the motor from turning; I used a stick to jamb the front of the motor; then unscrew the old blower fan and screw on the new one. Then replace the cover and put front panels back on.

First it was a process of alimination to find out why it was dropping out. After the problem was found it was just a matter of replacing the holding coil on the gas valve. Thank you fred kenney sr

To make working on the dryer easier we tipped the dryer back, about 45 degrees, removed the bottom panel, the door panel, note: make sure to mark the inside chassis or case with a sharpie where the wires go by color, etc… note: this makes it easy to place every thing back in order. I removed three screws on the bottom left side, to allow the more room for me to remove the drum. You can not remove the drum just yet but until the rubber belt is removed. I went below where the tension wheel is… it’s back behind the motor… incidental the tension wheel and the arm was the problem, it had warn to one side. Now release the rubber belt around drum. I pulled the drum out. The motor assembly is all one piece so it’s easy to remove. Don’t forget to unplug the plastic Molex plug and mark where you wires go. Two screws in front on the motor assemble and the whole assemble comes out. From here I could do a good job of cleaning the motor assemble and replacing the parts without any difficulty. Re-assembly was really easy, just one issue with placing the rubber belt took some time, and I need some help. I was finished in less than two hours. Bingo fixed!!

(I knew the gas coils were bad, since the gas ignitor would glow brightly as the burner attempted to ignite. So I knew everything except the gas valve was operating normally.)

Unplug the electrical cord to the dryer. Remove the front access panel. Remove the retainer clip for the gas coils (2 screws). Remove the coils and unplug the electrical connections. Connect the new coils to their respective electricl connections. Slide the nes coils back onto their respective posts on the gas valve. Replace the retainer clip, and 2 screws to hold it in place. (I then plugged the dryer back into the wall outlet to visually check the burner operation) Everything worked fine so I then replaced the front panel.

Unplugged dryer, turned off gas, raised front of dryer with two 2X4's on edge resting on legs, removed two lower panel screws, removed lower panel. Removed lower blower & filter assembly, screws (3) are on the inside of drum. (Good chance to clean it out) Removed two lower front upper main panel screws. Supported top panel with wood for access. Removed panel slowly, marked wires that go to door switch, set panel aside. Removed tension on belt by reaching in on the right lower side and unhooking the tensioner from belt, look to see how it is installed, for reinstallation on assembly. Pulled drum out slowly as not to damage seals on drum. replaced parts, attached with self tapping screws.(screws all the same size) reassembly in reverse order. Will need to put belt on drum before installing drum. Check drum alignment with rollers and seals. Used very small amount of high pressure grease on roller bracket and shaft assembly where the support roller shaft spins for lubrication. All's quiet. (Vacuumed out inside while dissassembled)

Removed front of dryer, unplugged each coil to determine where buzzing was coming from.....determined it was the boosting coil....ordered part and replaced. Dryer works great....we think it had be going bad over time because drying times have noticeable decreased.

I first ordered the coils from a different web site and they sent the wrong ones. The job would have been much eaiser if i had just returned and ordered from here. Instead i cut wires and tried the others but since they were worng, it did not work. I didn't label the wires so it was a puzzle to put it back together. Once i had the wires connected properly it was a simple fix. You just open the top and take the front pannel off, remove the drum and it is right there at the bottom. Two screws take the cover off of the coils and they slide off the gas valve. Slide the new ones on and replace the cover. Put the front pannel back on, close the top and its good to go. I first tried the highlimit thermostat, and termostat with no luck. The flame would light when it was cold, but once warmed up, the flame would ignite and immediatly go out. The coils did the trick.