ALE866SBC (PALE866SBC) Amana Dryer - Instructions

I only had to replace the old one with the new one. It was simple.

Very easy , Removed the front panel and drum. Swapped the pulley and put the unit back together

my husband took my laptop into our laundry room (he's never repaired a dryer before)and followed the repair tutorial on the part page step by step. He was VERY proud of himself and my dryer is working like new!

Disconnected The Power, Took The Front Panel Off The Bottom Of The Dryer. Remove The Black Plastic Duct, Remove The Steel Cover For The Blower Wheel. Spin The Blower Wheel Off While Holding The Motor To Prevent It From Turning. Remove The Blower Housing. Pull The Motor Forward, TAKE NOTE OF HOW THE BELT GOES ON THE PULLEY! Release The Belt From The Pulley. Remove The Motor From The Mount, Disconnect The Electric Plug From The Motor. Pretty Simple Really. Reassemble In Reverse!

Amazingly easy; watched a video a couple of times, then went right to work.

Removed front of dryer, first the lower then the upper front covers. Removed front drum support, front blower housing cover. Removed belt, and then motor with housing and blower wheel attached. Broke wheel and cover off motor, placed motor in vise to remove threaded nut from motor drive shaft (nut was seized). Reinstalled motor and belt. Installed new housing and blower wheel. Reassembled dryer. Note if old blower wheel had come off repair would have taken half the time and been significantly easier to perform.

Parts arrived the next day, yes, that was super fast. All parts were as ordered, much appreciuated. The dis-assembly was the hard part, getting the dryer open and figuring out how to remove the panels was hard because it was unfamiliar. I watched the videos prior to starting the work which were a reall big help. Actually, I would not have even tried this if it were not for the videos. After seeing the videos, I thought to myself, I could do that. The repair solved the problem 100%. Also, got a chance to really clean out the dryer vents and other areas. THANKS!

At first - my dryer started softly squealing when it was running. Then it got louder, and LOUDER, finally it was so loud - I had to go outside if it was running. A little diagnostic work helped me figure out that I needed to repair the idler pulley. While I was at it, I decided to replace the drum support rollers and the drum glides. The parts were about $40 total, and they arrived in two days. TWO DAYS! I only needed two tools to do the repair - a nut driver, and a pair of slip ring pliers. It took longer to figure out how to take the dryer apart than it did to make the repair. It didn't come apart the way most of the videos I watched showed - but I eventually figured it out. Once I removed a few nuts - everything was easy. The parts were replaced in two minutes - it was THAT simple. The hardest part was putting the drum belt back in place, threading it through the pulley. I had to watch the video three times, to understand how it was supposed to weave. But - it was a simple repair, and I probably saved myself $150-200. I'd use this website without hesitation, for any future repair. If you're handy, you can do this stuff.

I watched a PartSelect video of my repairs on YouTube which helped but they make it seem very easy and it was more difficult to perform. The videos do help.

Watched the video on the same web site where I found the parts! The video showed the exact model I had. Found that someone had left off the front washer on the Drum Support Roller and would not have realized this if it was not described in the video!

Fast delivery,,,, Easy installation

Followed the video from the same web site. If you don't think you can do the repair you are wrong. I ordered the two parts suggested just in case it was one or the other. Cost plus shipping was under $35. Helpful hint tackle the high limit thermal fuse first that's what was wrong with our dryer. If anything you have a good door switch on hand and still well ahead of the game. I'm glad my wife made me order it. Easy install. I sure it would have cost a hell of a lot more just to get some one to look at it and then fix it. I'm the type to just pay the money to get it fixed.

Noise sounded like a pulley noise so I decided to replace the drum rollers and belt and idler lever pulley. The problem was the idler lever pulley but it was a good idea to replace the other parts while the unit is apart. Not a difficult repair. Thanks for your video on how to replace parts.

We followed the video for the new rollers and now the dryer is like new and it's 18 years old.

Took old filter out put new one in