ALE643RBW Amana Dryer - Instructions

I removed the top cover and located the faulty timer. I then noted the part number, placed the order and the part came the NEXT DAY via regular mail! I replaced the timer, making sure to reconnect the wires to the appropriate connectors. The dryer has been working fine ever since. I am extermely pleased with PartSelect.com. I not only saved myself the price of a new dryer, but I also saved nearly 1/2 off the replacement part based on a quote from a local retail store.

I'm glad I found your website :)

Ordered new lint filter, which did not quite fit. Called company and was told that filter had been redesigned to remove the felt surround, and that sometimes the new filters did not seat well. It turned out that the exhaust pipe was filled with packed-down lint causing the new filter not to go all the way into the slot. My husband surmised that that was why the first filter broke because volunteers at the Humane Society adoption center were trying to shove the filter into a groove that no longer worked. He took off the top, the front, and one other piece before removing all of the lint he could reach. Once that was done, the filter fit fine.

first i checked the power supply then i checked each of the switches and limit fuses for continuity.
to do that i had to take the front of the drier off, four screws there. then i removed the bad limit switch 2 screws,the door switch was bad so i replaced it, no screws. since i had the front off the drier i removed the four screws that held the drum in place and replaced the belt. assembled the drier in reverse order when the parts came. 1/2hour total labor.

I first removed the two front screws on the front cover located on the lower half of the dryer using a flash light looking on the left side all the way to the back you will see two hex screws removing them will now let you wiggle the heating element back & fourth while pulling down it will come out in just a few seconds - then with your digital camera take a picture of the still wired heating element as to a clear reference for wiring the new element - first Aline the new element in the same direction as the old element and transfer them one by one check camera for assurance that you have done it correctly and re-reinstall in the reverse order

also I would recommend taking off that black plastic blower chute and cleaning it assuringly the best performance of air flow

I inserted the clip

Removed bottom door panel, four screws. The new part was a slightly different (looks like improved) part, so only had to put two screws back in. Very simple. The only reason it took more than 15 minutes was because I cleaned exposed areas while the panel was off.

Remove the 2 screws at bottom of front panel, remove lower panel. Then remove the two screws at bottom of front door. Lift door forward so spring hooks can disengage from the top panel. remove door, disconnect the 5 wires to the door latch and light. remove the two screws at top of dryer to lift up top panel. Remove 4 screws at the front holding the drum. Disengage the belt from the tension pulley and remove drum. Replaced both roller wheels at the rear of the drum( one was broke). Then remove the screws (about 6 holding the plate in front of the blower wheel. Use a wrench to hold the nut at the back of the motor and a scocket wrench to remove blower wheel. (The Blower wheel was broken from the shaft and was spinning freely). Then do it all backwards to re assemble. i spent more time cleaning the lint from the inside than I took making the repair!

Shut off or unplugged dryer for safety.

Slipped thin blade putty knife up under bezel of switch to unlatch from the panel and pulled forward to remove the swwitch from the dryer. Unplugged the quick connect terminals (3) from the old switch and plugged them onto the new switch. one of the terminals had gotten quite hot and darkened the insulation so it was replaced with one that was supplied with the switch. that was a cut, strip, crimp process. Placed the new switch into the panel and snapped into place.

Not too difficult. Take out of box, insert into dryer slot.
Done

remove bottom section under door 2 screws remove door 2 screws remove switch by squeezing tabs install 2 new female ends on wires supplied with switch . put switch back in plug in wires .

Dryer would only tumble for ~15 min then stop. During this time it would be really loud. Turns out to be a bad Motor. To replace 1) Removed bottom kick panel by removing 2 screws. 2) Then removed upper front cover by 2 additional screws. 3) Disconnected thermostat (marking location of wires on paper). 4) Removed blower housing (3 screws)undid the rib belt from the drum by pushing the pulley wheel up so the belt could be loosened and removed from motor. 5)Removed the front cover of the dryer opening by removing 2 screws. 6) Lifted up and then puled it out to expose the drum. 7) Removed the drum w/belt from the dryer exposing the motor. 8) Removed 2 screws from the motor and disconnected the plug from it. Slid it all the way out. 9) Need to remove (3 screws) the metal faceplate from motor to access the blower wheel (plastic). 10) Unscrewed the plastic wheel and removed 2 screws to remove the motor from the frame. reversed the process for reassembly. Sounds tougher than it really was - only took 30-45 min. Suggestion - write down on paper location of any wires you disconnect - makes reassembly very easy. Also recommend vacuuming any lint in the dryer while it is completely accessible.

1-Unplugged drier
2-removed lower panel-(2)-8mm screws
3-removed intake from fan-(3)-8mm screws
4-removed dryer's front panel-w/door assembly-(2)-8mm screws. (note there is a door switch you will need to disconnect the wires and remember which terminals they go to.
5-remove the front drum support-(4)-8mm screws
***** at this point the drum is exposed *****
6-reached under the drum pulled the tensioner to relieve tension on belt, then dismounted the belt from only the tensioner and motor shaft; leave the belt on the drum!
7-pull drum toward you and forward about 3-to-4 inches, this exposes the drum rollers.
8-use a screwdriver and pry-off the retaining clip on the end of the roller's shaft and remove the roller.
9-remove the roller support-(2)-8mm screws
10- reinstall new roller support
11- apply a light coat of disc-brake hi-temp wheel bearing grease to the roller support shaft, very light!
12-install a new wavy thrust washer, new roller(note they will say "front" on the side that should face you. Don't mount it backwards!
13-install the outer thrust washer and the new retaining clip; use a flashlight for this part!
14-repeat for the other drum roller.
**** while you have it apart use a vacuum to remove lint from every where you see it; it is a fire hazard!
**** if you think you need a drive belt now is the best time to change it *****
15- re-assemble the dryer in the reverse order, don't forget to re-install the drive belt and be careful not to pinch the door switch wires.
16-re-plug the drier and test

Replaced the recommended drum rollers, belt and tensioner, light bulb. Found repair manual online (bit of a hunt)made job easier still took 2.5 hrs. Then turned drum by hand no squeak. Turned it on and still squeaked. Isolated to motor. Replaced it (had to take dryer completely apart again but went quicker due to experience also had to disassemble the motor assy and rebuild. Took 1.5 hrs works like new now. The design of the dryer is not bad remove bottom front panel first, screws at very bottom of panel then two more screws are uncovered to remove front. It just lifts up and pulls out. then remove four bolts which hold front frame on (supports drum) all this has to be done to reach the replacement parts. drum wheels are held on by snap rings not the screws (real fun if you take them out) reverse to reassemble.

First I went to Maytag.com thinking it was best to go to the manufacturer for parts. Their search engine did not even recognize my part number. I tried every way I could think of. Then I just entered the model number in google and it sent me to the Partselect.com website. Diagrams came up and I chose parts from the pictures. The parts arrived in about 3 or 4 days and fit perfectly.

First I turned off the circuit breaker, then removed the two screws that hold the front lower panel in place. Once open I removed the 2 screws that held the element in place. (Far back left side) I then pulled the element out leaving all wires connected. Wires are long enough to extend out to the floor in front of the dryer. I simply exchanged the wires one at a time to the new element so no mistakes could be made. Reinstall, reset the breaker, and Instant HEAT. Repaired for under $40.00