Models
>
AK2T36W2
AK2T36W2 (P1143722N W) Amana Cooktop - Overview
Sections of the AK2T36W2
[Viewing 2 of 2]
Keep searches simple, eg. "belt" or "pump".
Radiant Surface Burner Element 1500W
PartSelect #: PS11764909
Manufacturer #: W10823699
This surface element is made for under glass set-ups and supplies the heat to a cooking area on top of the range. It has an outside diameter of approximately 7 inches (1500 watts), and is a genuine OE...
$106.72
In Stock
Electric Hole Cover
PartSelect #: PS11757450
Manufacturer #: WPY0307427
This hole cover is almost two inches in diameter. It fits below the surface burner knob of some ranges, and has a center hole just big enough for the knob's shaft.
No Longer Available
Dual Radiant Element with Limiter
PartSelect #: PS11764926
Manufacturer #: W10823726
With the dual element you are able to adjust the size of the burner you want to use to match your pots/pans.
$211.99
In Stock
Dual Element Infinite Control Switch
PartSelect #: PS2003805
Manufacturer #: 12002422
$119.64
In Stock
Screw
PartSelect #: PS11742713
Manufacturer #: WP488234
This screw is sold individually.
Size: 8-32 x 1/4 inch.
$9.13
Special Order
Surface Ribbon Element with Limiter - 8"
PartSelect #: PS11764914
Manufacturer #: W10823710
This is a 2000 watt 240 volt surface element.
$183.86
In Stock
Infinite Switch Knob
PartSelect #: PS2033416
Manufacturer #: 31760602W
This infinite switch knob is two inches in diameter. It is white in color and it is made entirely of plastic. There is gray lettering denoting the varying degrees of temperature.
No Longer Available
Surface Ribbon Element with Limiter - Small
PartSelect #: PS2034682
Manufacturer #: 32082801
This is a 1200 watt / 240 volt surface element.
No Longer Available
Questions And Answers for AK2T36W2
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the AK2T36W2
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Outer Heater ring not working on dual burner.
Turned off power to unit.
Tilted up Glass top and removed two screws holding rear hinges to range. Then I unplugged wire harness from lower range and placed the Glass top facing down on counter top with towel for cushion. Removed 1 screw holding center of burner to support frame, two alignment screws on perimeter, and two screws hol ... Read more ding support frame to glass top. This allowed me to slide out the old element with all wiring connections intact.
Placed the new assembly in same location under support frame, noting numbered positions of two alignment screws from old unit. This is necessary to properly align heater to surface glass. Replaced all screws connecting burner to frame. Then I removed each wire one-by-one from old unit, reconnecting to same location on new unit.
Replaced top in reverse order from removal. Powered on the circuit breaker and verified proper operation of dual unit with large/small selecttor switch. Total time to repair about 30 minutes.
Tilted up Glass top and removed two screws holding rear hinges to range. Then I unplugged wire harness from lower range and placed the Glass top facing down on counter top with towel for cushion. Removed 1 screw holding center of burner to support frame, two alignment screws on perimeter, and two screws hol ... Read more ding support frame to glass top. This allowed me to slide out the old element with all wiring connections intact.
Placed the new assembly in same location under support frame, noting numbered positions of two alignment screws from old unit. This is necessary to properly align heater to surface glass. Replaced all screws connecting burner to frame. Then I removed each wire one-by-one from old unit, reconnecting to same location on new unit.
Replaced top in reverse order from removal. Powered on the circuit breaker and verified proper operation of dual unit with large/small selecttor switch. Total time to repair about 30 minutes.
Read less
Parts Used:
-
Mark from Richardson, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
23 of 27 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner switch failed (full on, even in "lo")
Managed to reach down from the top, unscrew the old part, so I could remove from under the cooktop. Easy to trace the wires, and map them to the (slightly different) replacement. Works like a charm, and new part appears to be of higher quality than the old one.
Parts Used:
-
Stephen from Seneca, SC
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
21 of 33 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The infinite switch controlling one of the range top burners failed.
1 - Turned off electricity to the cook top.
2 - Removed the range top from the cutout in the counter.
3 - Removed the smooth top by removing the screws around the perimiter of the smooth top.
4 - Removed the screws securing the corner closest to the dead switch.
5 - Removed the screws holding the channel, onto which th ... Read more e infinite switched were attached, to the frame of the cooktop base.
6 - Removed the dead switch by removing the screws that hold it to the channel.
7 - One by one move the wires from the old switch to the new one.
8 - Reversed the process, 6 - 5 - 4 - 3 - 2 - 1, to put the cook top back together.
All in all the part was an exact replacement and the repair went really well.
2 - Removed the range top from the cutout in the counter.
3 - Removed the smooth top by removing the screws around the perimiter of the smooth top.
4 - Removed the screws securing the corner closest to the dead switch.
5 - Removed the screws holding the channel, onto which th ... Read more e infinite switched were attached, to the frame of the cooktop base.
6 - Removed the dead switch by removing the screws that hold it to the channel.
7 - One by one move the wires from the old switch to the new one.
8 - Reversed the process, 6 - 5 - 4 - 3 - 2 - 1, to put the cook top back together.
All in all the part was an exact replacement and the repair went really well.
Read less
Parts Used:
-
erik from chester springs, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
12 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!