Models
>
AK2T35W
AK2T35W (P1172104S) Amana Cooktop - Overview
Sections of the AK2T35W
[Viewing 3 of 3]
.gif "MISCELLAEOUS INFORMATION Diagram and Parts List for P1172104S Amana Cooktop")
Keep searches simple, eg. "belt" or "pump".
Cooktop Cleaner
PartSelect #: PS2344170
Manufacturer #: TJ114
Cleans/Polishes all glass, ceramic, porcelain and fiberglass surfaces.
No Longer Available
Radiant Surface Burner Element 1500W
PartSelect #: PS11764909
Manufacturer #: W10823699
This surface element is made for under glass set-ups and supplies the heat to a cooking area on top of the range. It has an outside diameter of approximately 7 inches (1500 watts), and is a genuine OE...
$106.72
In Stock
Dual Radiant Element with Limiter
PartSelect #: PS11764926
Manufacturer #: W10823726
With the dual element you are able to adjust the size of the burner you want to use to match your pots/pans.
$211.99
In Stock
Screw
PartSelect #: PS11742713
Manufacturer #: WP488234
This screw is sold individually.
Size: 8-32 x 1/4 inch.
$9.13
Special Order
Control Knob
PartSelect #: PS11740688
Manufacturer #: WP307620W
This control knob is just over two inches in diameter. It is white and made of plastic. There is gray lettering on this knob to denote the different degrees of temperature.
No Longer Available
Surface Ribbon Element with Limiter - 8"
PartSelect #: PS11764914
Manufacturer #: W10823710
This is a 2000 watt 240 volt surface element.
$183.86
In Stock
Dual Element Knob
PartSelect #: PS2030165
Manufacturer #: 307621W
This knob takes a double-flat shaft.
No Longer Available
Surface Burner Control Switch
PartSelect #: PS17307
Manufacturer #: 0309550
This dual surface burner infinite control switch is just under three inches long. Using 240 volts, this switch will operate at 15 amps.
No Longer Available
Questions And Answers for AK2T35W
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the AK2T35W
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Outer Heater ring not working on dual burner.
Turned off power to unit.
Tilted up Glass top and removed two screws holding rear hinges to range. Then I unplugged wire harness from lower range and placed the Glass top facing down on counter top with towel for cushion. Removed 1 screw holding center of burner to support frame, two alignment screws on perimeter, and two screws hol ... Read more ding support frame to glass top. This allowed me to slide out the old element with all wiring connections intact.
Placed the new assembly in same location under support frame, noting numbered positions of two alignment screws from old unit. This is necessary to properly align heater to surface glass. Replaced all screws connecting burner to frame. Then I removed each wire one-by-one from old unit, reconnecting to same location on new unit.
Replaced top in reverse order from removal. Powered on the circuit breaker and verified proper operation of dual unit with large/small selecttor switch. Total time to repair about 30 minutes.
Tilted up Glass top and removed two screws holding rear hinges to range. Then I unplugged wire harness from lower range and placed the Glass top facing down on counter top with towel for cushion. Removed 1 screw holding center of burner to support frame, two alignment screws on perimeter, and two screws hol ... Read more ding support frame to glass top. This allowed me to slide out the old element with all wiring connections intact.
Placed the new assembly in same location under support frame, noting numbered positions of two alignment screws from old unit. This is necessary to properly align heater to surface glass. Replaced all screws connecting burner to frame. Then I removed each wire one-by-one from old unit, reconnecting to same location on new unit.
Replaced top in reverse order from removal. Powered on the circuit breaker and verified proper operation of dual unit with large/small selecttor switch. Total time to repair about 30 minutes.
Read less
Parts Used:
-
Mark from Richardson, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
23 of 27 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Letters worn off from knobs
Our Amana stove top letters had worn off the knobs. We bought new knobs a few years ago and the same thing happened. This time we bought new knobs and coated the lettering with 5-minute epoxy to preserve the lettering.
Parts Used:
-
Joseph from Laurel, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
14 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacement of burner control switch
1. Open the circuit breaker feeding the range. Turn all range control switches ON to establish that there is no power. Remove all knobs.
2. Get under the range and remove the 2 hex-head screws securing the flex conduit to the bottom panel. Then remove the 20 hex-head screws securing the panel to the range. Lower the panel and place a ... Read more side, and then after checking for no voltage disconnect the red and black incoming wires by pulling on the spade connectors. Make sure you mark which wire went where.
3. From below apply pressure to the range frame to free the top surface gasket from collected food debris, then from above lift our the range and place upside down on a towel. Support the range with wooden blocks so that the unit is not resting on the knob shafts.
4. The control switches are all mounted on a common bracket with two screws for each switch. The first task is to remove two screws on each side holding the bracket to the frame, and then two wire harnesses on each side. Then gently move the bracket and rotate it sidewards so you have access to the screws holding down the switches.
5. Remove the defective switch leaving all the wires still connected.
6. Install the new switch and transfer the wires from the defective switch.
7. You're done, now restore everything in reverse, just make sure all wires move freely and not pinched.
2. Get under the range and remove the 2 hex-head screws securing the flex conduit to the bottom panel. Then remove the 20 hex-head screws securing the panel to the range. Lower the panel and place a ... Read more side, and then after checking for no voltage disconnect the red and black incoming wires by pulling on the spade connectors. Make sure you mark which wire went where.
3. From below apply pressure to the range frame to free the top surface gasket from collected food debris, then from above lift our the range and place upside down on a towel. Support the range with wooden blocks so that the unit is not resting on the knob shafts.
4. The control switches are all mounted on a common bracket with two screws for each switch. The first task is to remove two screws on each side holding the bracket to the frame, and then two wire harnesses on each side. Then gently move the bracket and rotate it sidewards so you have access to the screws holding down the switches.
5. Remove the defective switch leaving all the wires still connected.
6. Install the new switch and transfer the wires from the defective switch.
7. You're done, now restore everything in reverse, just make sure all wires move freely and not pinched.
Read less
Parts Used:
-
Farouk from Sudbury, MA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
10 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!