Models > AK2T30E4 (P1131576N E) > Instructions

AK2T30E4 (P1131576N E) Amana Freezer - Instructions

All installation instructions for AK2T30E4 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the freezer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the AK2T30E4
1-13 of 13
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Outer Heater ring not working on dual burner.

  • Customer: Mark from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 13 of 15 people found this instruction helpful
Turned off power to unit.
Tilted up Glass top and removed two screws holding rear hinges to range. Then I unplugged wire harness from lower range and placed the Glass top facing down on counter top with towel for cushion. Removed 1 screw holding center of burner to support frame, two alignment screws on perimeter, and two screws holding support frame to glass top. This allowed me to slide out the old element with all wiring connections intact.
Placed the new assembly in same location under support frame, noting numbered positions of two alignment screws from old unit. This is necessary to properly align heater to surface glass. Replaced all screws connecting burner to frame. Then I removed each wire one-by-one from old unit, reconnecting to same location on new unit.

Replaced top in reverse order from removal. Powered on the circuit breaker and verified proper operation of dual unit with large/small selecttor switch. Total time to repair about 30 minutes.

The infinite switch controlling one of the range top burners failed.

  • Customer: erik from chester springs PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 10 of 14 people found this instruction helpful
1 - Turned off electricity to the cook top.
2 - Removed the range top from the cutout in the counter.
3 - Removed the smooth top by removing the screws around the perimiter of the smooth top.
4 - Removed the screws securing the corner closest to the dead switch.
5 - Removed the screws holding the channel, onto which the infinite switched were attached, to the frame of the cooktop base.
6 - Removed the dead switch by removing the screws that hold it to the channel.
7 - One by one move the wires from the old switch to the new one.
8 - Reversed the process, 6 - 5 - 4 - 3 - 2 - 1, to put the cook top back together.

All in all the part was an exact replacement and the repair went really well.

Baked on sauce

  • Customer: Julie from Newnan GA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 8 of 10 people found this instruction helpful
Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.

Inner burner of dual burner element burned out

  • Customer: Don from Red Wing MN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 7 people found this instruction helpful
Pulled stove out and unplugged it (energized wire at burner even with burner turned off) Removed screws to lift cook top Removed burner support brace Removed three screws to remove burner Removed connections from old burner, installed on new burner Replaced screws in burner to brace Replaced burner brace Lowered cook top and installed screws Plugged in stove and pushed it into space

The high ekement on a dual burner range top burned out

  • Customer: Grace from Inverness FL
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers
  • 4 of 4 people found this instruction helpful
Turned off circuit breaker and unplugged. Opened oven door and removed 3 screws holding the range top to the range. Lifted top and proped open with a wooden block. Removed all 5 wires to the element and drew a diagram of where they came from noting the color code. Removed two screws holding the bar that supported the element
and dropped slightly while removing the two standoff screws holding the element in place.
slide the element out. The problem was that the element received from partselect.com did not physically match the terminals on the original. this required me drill out a brad on the terminal block cover to see how the terminal block was wired. I discovered that the different color wires on the old element went to physically different terminals on the new one. This was even though I had returned the first element received, got a new part no from matag and reordered.
there are tiny markings on the terminal block that helped show the way. Be sure to find them and rewire according to these markings. 1a 2a 1b 2b as the terminal locations may be different.
I am happy with the partselect,com and their attention to trying to get me the exact replacement.
Also happy with their return policy.

The burner was not heating up

  • Customer: Jeffrey from Miami Lakes FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 6 people found this instruction helpful
I removed only 3 screws that allowed me to lift the glass top on the stove. I removed the burner and I could see where it short circuited. I ordered the new burner element. After it arrived I replaced it by moving the wires from the old element to the new element, and put it back together.
I am sure that I saved at least $200 in "labor".

cook top was broke

  • Customer: Ed from Bellefontaine OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 9 people found this instruction helpful
we removed the old cook top sixteen screws and four bolts was removed put the new top back on and put all the screws and bolts back in job done

Outer element not working

  • Customer: Charles from Richmond TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 7 people found this instruction helpful
First we turned off the power to the range top. Then propped the range top on small planks of wood in order in order to get to the 12 to 15 screws that held the top to the base. Once we had the top (glass) removed, we removed the four screws holding the bracket that held the front and rear elements. We then removed the bracket and elements, turned the bracket and elements over to remove the two screw type legs that held the dual element. Once the dual element was loose we disconnected the wires and reconnected to the new element. Then reversed the procedure to reinstall.

element quit working

  • Customer: Donald from Jeffersonville IN
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
removed 2 screws holding top in place witch gave me ac access to none working part. removed 5 screws witch let me remove part, reversed order to reinstall part, very easy
Donald Carpenter

Range burner control switch had a direct short. Burner would not heat up.

  • Customer: John from Pride LA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
First I removed the two screws that held the switch in place and disconnected the five different wires to the device. Then I connected the five wires back in there same locations on the new part and placed it back into the mounting slot / hole. Then put the two screws back to hold it in place. Put the range's back cover back on and connected it back to the power supply box under the cabinet. Turned the breaker back on and turned the new burner knobs on high and got the red glow from the burners and the red indication lights from the range. Yeah, back in service just in time for Thanksgiving cooking. (Changed out 2 burner controls and replaced the hole covers on the switch knobs) Complete project. Thanks

Needed stove top cleaner and scraper

  • Customer: Doris from Camden-Wyo. DE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Absolutely perfect, no problems

Burner stopped heating

  • Customer: Anna from Copperas Cove TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
My husband did the repair. It was so easy that I could have done it. He had to remove 3 screws and then hook up the element. Nothing to it!!

cleaner

  • Customer: Mary from Duarte CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you
All Instructions for the AK2T30E4
1-13 of 13