Quick Question!

Have you ever purchased from PartSelect.com before?

Models > AK2H30W1

AK2H30W1 (P1131546N W) Amana Cooktop - Overview

Get Parts and Repair Help for AK2H30W1

If you know the cooktop repair part you need, you can browse the list of all parts on the AK2H30W1, or you can search by name or part description. You can also find your part by where it is located on the AK2H30W1 by selecting a section below. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the AK2H30W1

[Viewing 2 of 2]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.93

Electric Hole Cover

This hole cover is almost two inches in diameter. It fits below the surface burner knob of some ranges, and has a center hole just big enough for the knob's shaft.

Order within the next 8 hrs and your part ships today!
$4.90

SCREW

Order within the next 8 hrs and your part ships today!
$27.35

Control Knob

This control knob is just over two inches in diameter. It is white and made of plastic. There is gray lettering on this knob to denote the different degrees of temperature.

Order within the next 8 hrs and your part ships today!
$3.59

Screw

This screw is sold individually. Size: 8-32 x 1/4 inch.

Order within the next 8 hrs and your part ships today!
$50.73

Surface Control

This switch controls the stove top surface burner.

Order within the next 8 hrs and your part ships today!
$23.54

Dual Element Knob

This knob takes a double-flat shaft.

Order within the next 8 hrs and your part ships today!
$4.90

SCREW

Order within the next 8 hrs and your part ships today!

Control Knob

Sold Individually. This knob accepts a D-shaped shaft.

Surface Burner Control Switch

This dual surface burner infinite control switch is just under three inches long. Using 240 volts, this switch will operate at 15 amps.

Surface Burner Switch

This switch controls the stove top surface burner.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Letters worn off from knobs

  • Customer: Joseph from Laurel, MD
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required:
  • 12 of 13 people found this instruction helpful
Our Amana stove top letters had worn off the knobs. We bought new knobs a few years ago and the same thing happened. This time we bought new knobs and coated the lettering with 5-minute epoxy to preserve the lettering. read more

Replacement of burner control switch

  • Customer: Farouk from Sudbury, MA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 8 of 9 people found this instruction helpful
1. Open the circuit breaker feeding the range. Turn all range control switches ON to establish that there is no power. Remove all knobs.
2. Get under the range and remove the 2 hex-head screws securing the flex conduit to the bottom panel. Then remove the 20 hex-head screws securing the panel to the range. Lower the panel and place aside, and then after... read more

2 controls were damaged and not working correctly. One would not properly shut off.

  • Customer: Edward from Sunnyvale, CA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
1. Turned off the 240V branch circuit to the cooktop.
2. Removed and inverted the cooktop.
3. Removed the bottom panel, used 1/4-inch nut driver to remove the sheet metal screws.
4. Confirmed the circuit was de-energized. Voltmeter set to AC, measure across the L1, L2 connections, should be 0 VAC or very close.
5. Make a diagram of the ex... read more