Quick Question!

Have you ever purchased from PartSelect.com before?

Models > AGM429W2

AGM429W2 Amana Dryer - Overview

Parts and Repair Help for models starting with AGM429W2

If you know the dryer repair part you need, you can browse the list of all parts for models starting with AGM429W2, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for AGM429W2 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Models starting with AGM429W2

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$15.40

'M' Series New Style Coil Kit

This gas dryer ignition coil set comes with two ignition coils: one three terminal Boost/Hold coil, and one two terminal secondary coil. Usually only one of them burns out but you ...

$20.00

Multi Rib Belt - 93-3/8"

At 93-3/8" inches in length, this dryer drum belt from Amana has five ridges. It is all black in color and is made entirely of rubber. A flat belt, it is 3/8 of an inch wide.

$12.69

Drum Support Roller - for square ported models

This single drum support roller is used for square ported model clothes dryers. It has a metallic bearing in its center.

$7.86

Drum Glide

This drum glide is sold individually. ***Please Note: these should be replaced in pairs.

$8.55

Idler Pulley Wheel with Bearing

This two inch wide idler pulley wheel is beige in color and is made of plastic. This pulley wheel comes with its own metallic bearing in its center.

$29.50

Radiant Flame Sensor

This part senses the flame for heat allowing the gas valve to open.This flame sensor is three inches long and is used for many gas clothes dryers.This flame sensor assembly is made of both plastic and metal.

$7.22

High Limit Thermal Fuse

Meant as a backup to a high limit thermostat, this fuse is typically set to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when ...

$17.70

Idler Lever

The spring for this part is sold separately.

$5.15

Washer, Thrust

This washer is 3/4 inches in diameter.

$19.20

Cylinder Felt Seal

This part is located between the back of the drum and the rear dryer panel.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Drum not centered , clothes getting stuck in dryer

  • Customer: Chris from Hopedale, MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 490 of 498 people found this instruction helpful
The first thing I did was to unplug the dryer from the wall. Then I removed the bottom two screws and slid the bottom cover off so i could see all the way to the back, I tipped the dryer back against the wall and searched for the problem with a flashlight. I noticed that one of the guide wheels that held the drum in place was sheared off. I took the new d... read more

Squeeling and grinding noise

  • Customer: Steven from Holderness, NH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 431 of 441 people found this instruction helpful
Wasn't the belt!! Changed it anyway. Should have come here earlier. That mistake added several days to the repair waiting for a second batch of the right parts. Became a pro at taking the dryer apart and reassembling, though! Easy job, just take your time and mark your wires, if you need to.
Followed other people's excellent instructions. Clean out al... read more

Dryer ran but would not heat

  • Customer: Gary from Haverhill, NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 289 of 325 people found this instruction helpful
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are located on top of t... read more