Models > AGD4370TQ0 Whirlpool > Instructions

AGD4370TQ0 Admiral Dryer - Instructions

All installation instructions for AGD4370TQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the AGD4370TQ0
1,306-1,320 of 1,465
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer drum stopped turning

  • Customer: Arthur from Felicity OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Popped the left and right side clips that hold the top, took out left and right side screws that held front face on, disconnected the wire that went to the door, tilted the door to me and lifted up from tabs on bottom. The old belt was broke, so it was easy to get off. Put the new belt on the drum making sure that the rubber ribs were touching the drum then I put the belt on the tensioner pully and motor pully. I rotated the drum by hand at least 1 full revolution to make sure that the belt was on right and it wasn't twisted, then I put everything back together. Easy 10 minute job... Art

Does not turn or tumble

  • Customer: Charles Weston from Pikesville MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Well, to Figure the issue I took the entire thing apart. Actually a lot more than needed. I found the torn belt and ordered it. I did not realize I may need a new belt tensioner which is sold with a wheel for the belt to wrap around and be tensioned by. Actually the original just utilized a rubber c or u shaped design(no wheel) for the belt to slide over. Anyways, instead of ordering and waiting for a new wheeled belt tensioner, I installed new belt with all original parts and working fine. I did oil up the drum rollers to reduce noise. And since I took the whole thing apart I cleaned the lint from every place it could hide. Ps a coke can is said to be helpful to hold the drum up while installing the belt but I found a jug of laundry detergent did better. Totally easy project for someone with no appliance repair history

broken belt that makes the dryer drum go around

  • Customer: kevin from madison WI
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The broken belt was found when I opened the dryer. The part number was on the belt and a quick online search led me to PartSelect. The part was available, delivered in less than 2 days and there was an online video showing the entire repair in detail.

Drum not turning / belt broken

  • Customer: Jill from Bangor PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I won't tell you how we did it, but I'll tell you the right way. Unplug. Remove the exhaust tubing attached to back of dryer. Pry the top up from the front and lean it against the wall. Un plug the wires attached to the front panel (remember where they go) Remove screws at top sides of front panel. "lift up" and remove. Close top. Lay machine on its back. We used a couple of 2x4's to lay it on so as not to crush the vest collar. Clean it out, including lint filter. The new belt wraps around the drum, you will see the channel about midway on drum. Feel behind the motor on the lower right side. There is a shaft with a channel for the belt. Immediately next to that is another pulley type arm with another channel for the belt. This arm moves stiffly and puts tension on the belt when installed correctly. Look at the diagram included with the new belt which shows the path of the belt. Wrap the belt, ridges against the drum and then around the motor shaft. At this point you have to physically pull the last arm out to allow the belt to wrap around the channel provided. If the belt is not twisted , the job is done. Turn the drum with your hands to make sure it is turning properly. Replace the front panel, plug in the electricals, replace the screws making sure the drum is properly centered. Stand up the dryer. Plug in and turn on dryer to make sure everything is right. Replace the exhaust tubing and set into place. Sounds like a lot of steps but I have described the whole process for you beginners. The rest of you will know already. Good Luck . Oh by the way we are 69 and 71. If we can do it, so can you

Broken Drive Belt

  • Customer: Cosmo from Somerville MA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed two screws at the top, removed two screws for the front panel, removed the broken belt, installed the new belt, followed the directions that were in the new belt package, and replaced all the panels and tested. It worked.

Installed a new belt

  • Customer: Timothy W from Lakeland FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
The video you had of my dryer was different then my dryer and the pulley was in the middle of the bottom and the motor and fan were in front of it. I had to replace the belt without being able to see what I was doing. I couldn't get it at first then realized there was tension on the pulley wheel and had to pull it towards the other wheel in order to get the belt on there. Once I pulled the wheel it went on really easy. My first time working on a dryer but I knew I could do it myself.

broken dryer belt

  • Customer: Thomas from Waterford NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
instructions were clear and repair was easy

Broken belt

  • Customer: Clayton from Girard KS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed video instructions. Raised the top, slipped off the front, installed the belt, aligned, installed tension part, reinstalled front, lowered the top and inserted lint trap. Job done. Quick and easy. The video was the key to the whole project.

Broken drum belt.

  • Customer: Bradley from Palm Bay FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
This was my first dryer repair. The only difficulty I had was figuring out how the belt tensioner was set up with the belt. The old belt broke so I didn't know how it was suppose to work. Anyway, it took a few minute to figure out that one end of the bracket was a "spring" that allowed it to flex a long ways! Pretty easy job.

We took towles from the washer that had still contained more water, the spin cycle must have had a problem.

  • Customer: Henry from McLean VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I felt the belt had broken since the unit was still running. I went on-line looked at some you tube movies to get some idea what to do. Was very helpfull. Found on-line how to get the part forb this nearly 20 year old dryer. Had the part shipped overnight, was able to track it. Followed your innstallation instruction, With the heavy rubber bands hooks at both ends it was easy. Never done this before, sure saved a good amount of money.

Broken drum belt

  • Customer: Barry from Norfolk VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Used the putty knife to pry open the front of the top cover. Removed the retaining screws securing front cover to each side. Lifted front panel off bottom hooks and holding drum, removed front cover. used wood block to hold drum in place. removed broken belt and belt tension spring. Keeping the rubber side of the belt against the drum, threaded belt through the tension spring onto the drive motor flywheel. Tilted dryer backwards to hold drum in place while removing wood block. Assembled front and top in reverse order. Used pressure to secure top to spring clips.

Belt Broke

  • Customer: Jeffrey from Grantsville MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Had an idea how the repair would go. The video is a great tool for someone not mechanically inclined. Easy fix and will save from paying a repair person. Suggestion .... put a small block of wood (or something simular) under the drum when you pull the front cover forward to save from having the drum drop down making sure the back seal is still seated and in place. No big deal and easily fixed if it pulls away.

Belt broke.

  • Customer: Laura from Saint Albans NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After looking at your video, my brother and I put the belt back on, placed the front and back on and that was it. It required two of us but it went well and the machine is working fine. Thank you.

Dryer Belt broke after about 10 years of use

  • Customer: Steven from West Point NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
We noticed the drum wasn't spinning, but the heat was turning on. About 3 years ago the heat was broken and it turned out that there was a little thermal fuse in there that needed swapped out, that was easy too fix too. Anyway, I looked up on youtube how to change out dryer belts on maytag units and it looked pretty straight forward. The model they showed was easier to access than my model, but I was able to still figure it out. Just pop off the top panel (they used a putty knife at the two clip points on the front, but I just yanked it up with a little force and it popped right up). Then unscrew the two little screws holding the front panel on, then pull off the front panel completely. This exposes the drum. The example on youtube showed easy front access to the belt assembly, but in my model, there was a stand for the drum as well as the drum motor in the way. So I just pulled the whole drum out the front most of the way, then I went behind the drum where I had exposed the pully/motor shaft assembly and then fed in the new belt into belt tension assembly that connects to the motor. While keeping it taught so the ribs of the belt would stay on the motor head (I had my wife hold it taught) I pushed the drum back toward the hanging belt and then worked the edges of the belt around the drum until it once again was completely around the drum. Then I slowly pushed the drum all the way back into place while continually working the belt back into place as I went. I then manually rolled the drum around a few times to ensure it was rolling correctly and that the belt was indeed in the right place. After a few good spins without it changing position, I reassembled the unit. It was very painless and took about 15-20 minutes in all. Works just fine again.

Belt had broken

  • Customer: George from Long Valley NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the online video three times. This was extremely useful. I just did what it showed. I doubt I could have fixed it without the video. This has got to be the best feature of the internet. I didn't have the exact model number, but the belt fit. I was surprised at how close the tensioning wheel was to the motor. Perhaps the belt will stretch with age and use.
All Instructions for the AGD4370TQ0
1,306-1,320 of 1,465