AFI2538AEW00 Amana Refrigerator - Instructions

simply repalced

I snapped the cover plate to the filter open. Pulled the filter down and twisted counter clock wise to take filter out. I installed the new filter in by inserting the filter and tuning clock wise to secure the filter. I flushed the water for about two minutes and then allowed it to be put back into service.

My son in law was able to take off the defective end pieces, and replace them with the new ones, in about 20 minutes. 10 minutes were probably spent in finding the right tools.Very easy to do. Parts were received within 2 days of ordering (I placed order on a Sunday).I was able to find the parts right away on your inter net lay out.

I first change the board behind the touch pad on front of ref. That controls switching from ice to water and temps. Problem ended up being the actual touch screen itself. Part select was great helping with parts and return first part and shipped touch screen out asap.

followed instructions step by step, everything went right in place and works perfectly. I could do it again inless time now that I seen what I was doing wrong on the back piece. (hope I don't have to) Thanks for asking.

Was little difficult to push in the new one, used a little force,

unscrewed old part, threaded temp control arm, screwed in new part

un plug first then locate part to replace.lower left corner facing the back . snap off cover on the compressor unplug capacitor install new one.left of capicitor remove the screw on relay install new one.done

Replaced the center rail

After years of using a flash light to check the contents of my refrigerator, I decided to try to fix the problem myself. Replacing the light switch was very easy. The directions were straight forward and I'm sorry I waited so long to tackle the problem.

This is the second order we have placed from Partselect. It arrived within two days as promised. The repair took about ten minutes and consisted of removing the deli drawer, removing the broken end cap, removing the slide rail from the end cap, cleaning out the area with a sponge, attaching the slide rail to the new end cap and installing the new end cap. The deli drawer easily slides onto the rails and the deli door easilt locks into place within the side rails. We were unable to locate the part locally and from now on, Partselect will be the first place we look for an appliance replacement part.

Took out 2nd new filter $43.00 each that clogged in less than 2 weeks each and installed in 2 mins. this bypass and ice and waterr work perfect.Thank you, thank you for your exceptional service ordered part and it came next day without extra charge,great service.

I took out the two shelves that were in the way. Lifted the glass out and set it aside. Since the pantry drawer cover wasn't in, because the tab was broke, I lifted the support beam out, pulled out the drawer and lifted it out. (The pantry drawer just lifts right out, straight up then towards you) I took out the back support beam, it lifts straight up. After that, I used a screw driver to take the pantry drawer glider (part #12) off of the broken one, then I put it on the new one so I wouldn't forget its orientation to the new part. I used a my socket set to take out two (should be three, but mine had two) bolts. I then gently pulled off the part needing replaced, first pulling it to the left, bringing the SLIDE- TEM (part #11) the BAR- TEMP (part #15) with it. Part #11 is held in by a tab at the back, to the left, so when you have the whole thing at the correct angle, it just slides out. (Pulling to the right, when you have the whole piece angled towards the center of the fridge, to the left.) After you get that piece out, you'll be able to clean the bottom of the fridge, it's amazing how much crap builds up on the bottom! (I even found a dead fly, eww! LOL) Taking parts #11 & #15 off of your old piece is easy, two tabs that you bend in on the right side of part #11 loosens it from your old part, then twisting it to take the pieces apart then lifting a few tabs to get #15 off of the old part. Then twisting it again to get the KNOB-TEMP (part #14) off. Pay attention to how you take this apart! It goes back together just like it came off! Attach these pieces to your new piece then it slides right in like you took it out. Slide the back left of #11 into the tab, reinsert the bolts, put your support bars back in, put your drawer in, put the drawer cover back into the new tab you just installed, put your glass in and finally, your shelves. All done!

I took the item from the box and snapped it in...12 sec. job.. what I did like is that I ordered the part,in 5 minutes and recieved the part in 3 days...great !!!! and thank you

Just replaced the old Push-On Start Relay and it started to work again.