Models > AFD2535FES > Instructions

AFD2535FES (AFD2535FES0) Amana Refrigerator - Instructions

All installation instructions for AFD2535FES parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the AFD2535FES
841-855 of 900
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice maker not making ice

  • Customer: Warren from Houma LA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I started by changing the water inlet valve. It made one batch but it did not eject into the ben. I removed the ice maker and found that the coating inside was bad. I changed out the ice maker and it is now making lots of ice.

Ice maker quit

  • Customer: Peter from Johannesburg MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed contents of freezer as this was a bottom unit. I had to remove freezer drawers/door to easily access ice maker which was located in the back of unit,wasnt a problem.I did however take a hair dryer to water tube as it froze up with about an 6 inch tube of ice that finally slid down. Connected unit and had ice within an hour or so and a full tray within 24 hrs. Second ice maker in little over a year...Video very helpful, saved 100 bucks by doing myself. Part arrived fast, great job!

Ice maker leaked a little, then quit completely.

  • Customer: Steve from Lansing MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
We ordered a PartSelect PS2121513 ice maker. I was concerned that there was no instructions shipped with the unit. Fortunately, PartSelect had an online video that guided me through the process. It wasn't that complex really. The only time I felt totally dumb was when using my nut driver to remove the bottom bracket. I couldn't figure out why there was no 1/4" socket with my set, so I used a small socket wrench instead. I finally figured out that the driver was already a 1/4", without a socket in it. After that it was easy. Slid the ice maker up a little to free it from the top mounting screws. Pulled it outward a bit to gain access to the connector at the back of the freezer, then squeezed the two sides of the connector and out it came. I popped the plastic cover off the existing device and then removed the connector as instructed in the video. I also removed the bale (as per the video). I put the connector harness, plastic cover and bale on the new ice maker and put it back in, this time using the nut driver on the bottom bracket :-). My only concern after that was that it didn't seem to be working. I had no idea that it needed some time to get cold before it would work. After about an hour, it filled with water and began making ice. Success.

the ice maker stopped working

  • Customer: Patrick from Barnegat NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
turned off the water supply,disconnected the power from icemaker to the back wall,loosened the two screws on the top,and one screw on the bottom.removed old icemaker.took the bale off,to put on the new icemaker.removed the wire harness from the old,to put on the new icemaker..saved over $200 for the repairman,had a full tray of ice in 6 hours.(watching the video,helped)!!!!!,very thankful for your service,as most of my appliances are all in that ten year period,i will be ordering more as needed.

Icemaker making icebergs, then nothing.

  • Customer: Edward from Burnt Hills NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The icemaker in my Maytag refrigerator was having a few problems. First, a small leak developed in the ice cube tray, allowing water to drip into the ice bucket. This of course caused the ice to become one solid mass, totally inappropriate for a gin and tonic. After a couple of months of this, it stopped working altogether. On to the internet I went, and discovered how easy this repair actually was. One nut to remove, one to put it back in. The installation video was very helpful. I did have a concern at first because the icemaker did not start making ice rights away. I thought it might be a defective unit. It took about 12 hours to get the first batch and it has been happily cranking out the ice since! Ed in upstate New York.

Ice maker drips water, making a blob of ice in the compartment

  • Customer: Charles from Metairie LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Empty out freezer loosen two top screws and took out bottom screw. Lifted out ice maker and unplugged wire. Took bailing arm and plug and put on new ice maker and reverse the process. Had ice in three hours and no leaks.

Old ice maker element burnt out

  • Customer: David from Bonita CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed wiring from old ice maker and install on new. With 2 screws all ready in place hung ice maker on them. Attach wire connector into socket and install bottom screw to hold ice maker. Tighten top 2 screw and put wire guide in place. Drop wire guide down and ice started in 10 mins

Icemaker not making ice.

  • Customer: Eleanor from Kennedyvillle MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the video as a guideline. It was not exactly as portrayed. My husband and I, being long time do it yourselfer's, were able to get around the differences. There were screws, instead of tabs as pictured in the video, plus had to remove 4 screws instead of one to loosen the old icemaker. After 2 days the icemaker is pumping out loads of ice.

Icemaker making a clicking noise not dumping ice.

  • Customer: RICHARD from COLORADO SPRINGS CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Rmoval and replacement is not at all complicated. (1)Reach behind and to the left of the icemaker and release the power plug. There is a release snap on th side of the plug. (2)Using a 1/4" nut driver remove the screw holding the icemaker to the "L" bracket at the bottom of the icemaker. (3)Using the nut driver loosen two self taping screws holding the top of the icemaker to the side of the freezer compartment.(4)Lift up on the icemaker to remove it. (5)remove the white plastic cover from the front of the icemaker (pry out at the bottom) and snap it onto the new icemaker. (6)Remove the wire sensor arm from the old icemaker and place it on the new one. (7) Remove the cable assembly (plug) from the old icemaker and fasten it to the new one. (8)Secure the new icemaker in place using the reverse order as the removal. The icemaker will take a little longer to make its first batch of ice as it will have to attain its proper operating temp (0 degrees to 2 degrees F).

ICE MAKER--NO ICE

  • Customer: ALTON from POQUOSON VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
DISCONNECTED POWER--REMOVED ICE HOLDER TRAY--REMOVED ICE MAKER END CAP--DISCONNECTED ELECTRICAL WIRES--REMOVED ONE SCREW HOLDING ICE MAKER TO REFRIGERATOR--LIFTED UP ON ICE MAKER TO REMOVE IT FROM TWO HOLDERS--TOOK CONTROL WIRE FROM OLD ICEMAKER AND INSTALLED IT ON NEW ONE--REINSTALLED NEW ICEMAKER IN REVERSE ORDER.

ice maker would not cycle. coating on ice tray was flaking

  • Customer: william from marydel DE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Since I had more than one issue, I decided to replace the entire ice maker. All I needed was a nut driver and it took 5 minutes. Three hex screws and unplug the wire harness and the whole unit came out. I changed the harness over and installed the new unit. I left for work and came home to ICE. It was Great!!!

Ice maker was producing large wet clumps

  • Customer: Edmund from Fallbrook CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
1. Viewed the video furnished (very helpful) 2. Turned off circuit breaker (avoids having to move the refrigerator), took my chances and left the water on 3. Removed the ice bin 4. Removed bottom retention screw, loosened the top two screws 5. Lifted the old ice maker free of top two screws 6. Used the bright flashlight to see how to release the rear electrical connection 7. Placed old unit on toweling, removed the electrical harness, the bail and the lower retention offset bracket (needed because the Kenmore's bottom retention is toward the center of the ice maker) and reinstalled them on new unit, taking care to maintain the original harness clip method 8. Carried the new unit to the refrig and installed the rear harness connector, then lifted it to mount on the top screws, forced it down to correct position, installed lower screw and tightened all three. 9. Placed bail in 'Operate' position, Installed bin and turned on the power. 10. Next morning, success!

Ice maker was leaking into the cube tray

  • Customer: Richard from South Lyon MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Once I received the new icemaker, I removed the old one by loosening the two upper screws and removing the lower. The wire connector came out easily. The wire and the bale from the old unit had to be transferred to the new unit. Then the new unit was reinstalled and the wire plugged back in. It took several hours for the cubes to begin dropping.

not made ice

  • Customer: Sunny from RICHARDSON TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The part came in 5 days from time order. take less then 10 minute done. part work well, have ices again, Thank you Part Select. we don't have to buy a new Rerigerator

follow the video that PartSelect has online

  • Customer: Rich from Wickenburg AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Watch the video and then do the repair.
All Instructions for the AFD2535FES
841-855 of 900