Quick Question!

Have you ever purchased from PartSelect.com before?

Models > AER5715QAW > Instructions

AER5715QAW Amana Range - Instructions

All installation instructions for AER5715QAW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the AER5715QAW
31-45 of 215
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven failed to maintain the set temperature.

  • Customer: Thomas from Clarksville, MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 8 of 8 people found this instruction helpful
Removed the old sensor by removing two screws and pulling the wire out through the hole. Disconnected the connector and discarded the old sensor.
Selected the correct connector of the 3 provided, plugged the new sensor in and threaded the wire back into the hole paying special attention to make sure wire and connector was on the backside of the insulation. Assembled the two screws and tightened.

F1 code and oven wouldn't operate

  • Customer: Robbie from Hillsboro, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 9 of 12 people found this instruction helpful
I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on. Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.

Oven door locked and was flashing code F4

  • Customer: Mary L. from Trinity, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 10 people found this instruction helpful
First, thanks to PartsSelect for getting the part to me so quickly. I went to the "Instant Repairman" , checked all that applied to my problem. The answer was the sensor, 99% of the time.I used a coat hanger to pull the latch back and open the door. I watched the video and followed the instructions to remove the old sensor. The wires were melted but the plug was still good. I used one of the adapters to install the new sensor, then replaced the two screws inside the oven. I pulled the stove out because I had read in the reviews that you needed to get the plug behind the insulation away from the oven wall. I was lucky ,there was a small hole in the back ,right behind the sensor.I gently pulled the wire and plug to the back ,well away from the oven wall. Put the stove back in place ,threw the breaker and was back cooking again!! My stove has a downdraft vent, took me longer to hook the vent back up than to install the sensor..Oh yes, did I say,I am a75 year old female and I did it all myself..

door glass broken

  • Customer: Mariano from Staten Island, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 19 people found this instruction helpful
My wife called a service company and was told that a tech would have to inspect the stove.
service charge 60.00 After inspection the parts would be orderd and a 200 fee for labor plus the parts would be charged at the completeion of the job. 2 weeks for part. I found you on the net orderd the glass. got it in 2 days and I completed the repair in 20 mins. Cost 89.00

1998 oven unit flashing F3

  • Customer: chris from houston, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 13 people found this instruction helpful
SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.

Burner heat does not turn down

  • Customer: Gary from Blanchester, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 7 people found this instruction helpful
Turn off breaker.
Remove knob, pulls off. Pulled stove away from wall.
Removed front panel with switches attached.
There are screws in front and back.
Removed screws that hold switch in place.
Transferred wires one at at time to get proper location.
Reverse process for reassembly
Gary in Ohio

I turned off the range breaker and doubled checked to make sure the power was off . Using 1/4" ratchet wrench I removed 2 sheet metal screws and lifted the glass top up and held it in up with a small cardboard bow. I removed 2 more screws holding the element in place and installed new unit. I then

  • Customer: Howard from Citrus Springs, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 7 of 8 people found this instruction helpful
See description listed as problem

Oven door was not closing all the way

  • Customer: Odin from Warrensburg, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 13 of 26 people found this instruction helpful
First I released the lock on the oven door hinge so that I could take the door off by lifting it up and out. Then it was just a matter of removing screws, replacing the hinges, and putting it back together. I did have to guess a little as I started removing screws as I wasn't sure exactly what to remove, but it became pretty self evident as I looked it over. Not as bad as I had expected.

Burner would only cook on high setting or not heat up at all.

  • Customer: Judy from West Salem, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 8 of 12 people found this instruction helpful
Shut off power to stove. Moved stove out. Loosened screws in top and middle back of stove and removed cover. Took mental note of color order of each wire and unhooked each wire from old switch and reattached to new switch in exact order of color of wire as original. Remounted cover on back of stove and reattached screws. Turned on power and turned on burner and tested burner for heat. Turned off burner, slid stove back and bingo - done. Saved a lot of money.

accidently broke the glass during cleaning

  • Customer: JOSE from DIAMOND BAR, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 12 people found this instruction helpful
replaced glass....fairly easy to install.

set oven to self clean and the inner glass broke

  • Customer: Garry from Livermore, CA
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
I removed the door from the oven and set it on towel on the table, and started the repair of the door. I removed the screws one at a time, and one layer at a time. Becareful you need to take the whole door apart, and remember how it goes bact together. In the end it was worth it. The hardest part was getting the right part. I thought I could order the whole door, and found out after several calls they don't sell the whole door. Part Select both times I put in my order had the parts at my door within 2 to 3 days. I also had to return one of the parts and within 2 to 3 days the part was credited to my account

glass on oven door broke

  • Customer: Petrina from Dracut, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
First we loosened the oven handle which required removing 4 screws. Then we removed the bottom piece which the glass sits on which required removing 5 screws. Placed the double stick tape on the frame then placed the glass on. We then put the bottom piece back on, tightned up the oven door handle and we were done. lrss than 1/2 hr later. This dose take 2 people to do otherwise you might drop and brake the glass. One thing I will say is that the oven glass did not come with the double sided tape to don't forget to order it. Also, there is only 1 piece of tape per package so order the proper amount your oven requires.

I leaned on the door and broke the hindge

  • Customer: Norman from Brockton, MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 9 of 17 people found this instruction helpful
I had a lot of trouble unlocking the door hindge you must pull the door out to change the hinge they are on the hinge and slide foward then pull the door up and out lay the door flat on a table cover the table with a towel so you don't scrach either one. Unscrew 6 screws on the door cover. 3 on top 3 on bottom take the cover off the hinges are exposed there 3 screws on the hinge 1 on the front and 2 on the bottom replace hinges install face insert door and lock the hinge it's all done. I wish I had these directions

Replacement of bad switch

  • Customer: Don from Roanoke, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 12 people found this instruction helpful
I marked all wires separately attaching a paper strip with tape to each connector and made a separate small chart where each wire should attach to the bottom of the switch. On this particular model there are three or four colored wires and two have both double and single connections to the same switch so the small chart told me where a single or double connector would attach even if I lost the attached taped information. Then since wires were marked separately, even if paper was lost I could still proceed with no outside help.
I had the luxury of leaving the breaker shut off while waiting for part to arrive. After arrival which was only a couple of days, I raised the stove top and let it rest on a small board maybe 1.5 feet so it would keep itself up.
The under assembly was already taken loose before so I just removed the broken switch taking all wires loose, which are already marked and replaced the switch with the new one. Gently placing each wire at its place after removing the tape for that connection. After all four wires were connected I held the switch up in place while screwing the two set screws into place. Then reattached the bottom assembly cover and then let the top down and reattached the four screws, one in each stove hole to attach the stove top to the under assembly. I then reattached one element and flipped the breaker switch on. No sound or problems so I tried the element and all is well. Reattached all elements and the project is done. PartSelect.com made this repair easy and economical. Replacement would have been 4x the part and shipping. Thanks.

Original oven light lens had cracked and broken in two.

  • Customer: Pat from Bucklin, KS
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 14 of 33 people found this instruction helpful
I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).
All Instructions for the AER5715QAW
31-45 of 215