AER1360AGW Maytag Range - Instructions

Super easy; pulled out broken element and pushed in new element. Wonerful service, communication, shipping. Received part in Seattle and mailed it to Hawaii installed without a hitch. Thank you

Just followed the instructions in the video!! A repair service was going to charge $95.99 just to walk in the door!!I I just ordered the igniter part. Watched the video and I know I can do that too!! I have only had one self igniting burner for years - didn't want to pay for a service call. Love your company!! Thank you!

finished removing door seal, used pliers to remove old securing studs. positioned new seal and pushed securing studs into existing holes and was done.

Turn off power (at breaker panel). Pull out range from wall and unplug electrical cord from outlet. Remove retaining screw at each side of element. Slowly pull out element from back of oven to expose electrical connector. Use pliers to pull connector apart (do not pull on wire). With element disconnected, measure resistance between the two ends of the element. Found infinite resistance or open circuit. Ordered replacement part and measured new part to be 20 ohms. Installed new element by pushing on connectors to new element. Carefully push new element into oven back wall and secure with the 2 screws. Plug electrical connector into wall socket and push range back to the wall. Turn on breaker switch. Turn on oven to verify fix. Note: Confirm there is voltage on both legs of wall socket for 220 volts which will confirm the breaker at panel is functioning. This can be done before removal of element from the range.

used drill to remove old screw

Simply remove the two screws in the back and carefully work the element out taking care not to pull the wires off. I left the oven door on which made access somewhat awkward reaching in. Remove wire clips and install new element in reverse. So easy even a caveman could do it.

I was unable to remove the screw which held the electrical element.. so I took the new surface burner receptacle and removed the metal part, and used the old one and put in the new one in the old metal part and rewired, and it is like new.. now I need to do another one.

unplugged the oven from the 220 volt receptacle. Removed the wire shelves. Unscrewed the two screws holding element to rear of oven. (I didn't know at this point to pull the wires through from the back so I took the back panel of the oven off and unplugged the connectors from the rear). Measured the defective element, ordered, and two days later I reversed the process when the package arrived in the mail. . quite simple. I love it when I can fix something myself. And by fixing, I actually mean "replacing".

followed you tube instructions. Very helpful feature. thanks

I have worked in maintenance field most of my adult life and all aspects and to change the oven door gasket was no challenge what so ever. It took longer to find my needle nose pliers to remove the old gasket clips and then re-install the new gasket. Maybe 10 minutes total

Remove both oven racks. Remove the screw that is on each side of the element holding it in. Pull the element out and disconnect the wire on each side of the element.Remove the bad element and replace it with the new element. Connect the wires to the new element and gently push the element back into place. Put the screws back into place and tighten. Replace the oven racks into oven. Turn oven onand verify that the element is heating. Repair is comlete.

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

I first pulled out stove, then disconned the power supply. Then removed rear panel which exposed connections to the bake element which was shorted out against one side of the rear panel. Replaced the bake element, then the rear panel followed by pugging in the stove and pushing it back into place then opened the oven door and tested the element to see that it was working properly. Thank you Partselect for your fast service on getting the part that I needed quicky and at a fair price.

I think the installation instructions are fairly self explanatory. This is the second item I've ordered from Parts Select and I'm thrilled with their service. The items are always less expensive than other sites and they deliver what they promise. I would highly recommend them.

Popped in there real quick. Wish I would have done it sooner, my oven heats up much faster.