Quick Question!

Have you ever purchased from PartSelect.com before?

Models > AER1360AGW

AER1360AGW Maytag Range - Overview

Get Parts and Repair Help for AER1360AGW

If you know the range repair part you need, you can browse the list of all parts on the AER1360AGW, or you can search by name or part description. You can also find your part by where it is located on the AER1360AGW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for AER1360AGW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$38.68

Bake Element

This bake element has push-on terminal ends.

$8.84

Surface Burner Receptacle Kit

This kit comes with one ceramic block, metal bracket, wires, and hi-temp wire nuts.

$5.15

Screw

This screw is sold individually.

$7.60

Levelling Leg

This levelling leg is just under three inches long. It is all black in color and is made entirely of plastic.

$5.15

Screw, 10-16 x 1

This screw is sold individually.

$35.15

Infinite Switch for Eight Inch Range Burner

This infinite switch for eight inch range burners is almost three inches long.

$35.44

Drip Bowl Kit - Light Gray

This is a kit of 4 drip bowls - Two 6" and two 8". All pans have holes in the bottom and they are light gray in color.

$45.79

Broil Element

This broil element is found on the roof of the oven.

$46.94

Oven Rack

Used in the lower oven. Sold individually.

$41.22

SEAL- DOOR

This door seal is fifty-three inches long. It is all black in color and is made of rubber. There are metallic clips sticking out of this seal at various points. These clips help to secure the seal to range doors.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Stove top element not working due to bad receptacle.

  • Customer: Richard from Carthage, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 139 of 150 people found this instruction helpful
Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.
My sister's husband wanted to... read more

The element broke in two pieces after food dried on it.

  • Customer: Heather from Huntsville, AL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 123 of 127 people found this instruction helpful
First, I unplugged the oven. Then, I removed the two screws that hold the element in place. After that, I gently pulled the element toward the front of the oven until the wires were exposed. I disconnected the wires from the old element, removed the old element and then attached the wires to the new baking element. I gently pushed the new element back in... read more

The Burner was getting too hot and you could not regular the tempature

  • Customer: Dennis from Hagerstown, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 46 of 52 people found this instruction helpful
Moved the Appliance out unplugged it and removed the backing plate then Remove the Knob and unscrew the infinite switch then marking the 5 wires to know where the go on the new switch, removing and replaced it with the new one read more