AEQ6400HS0 Frigidaire Dryer - Instructions

The repair went very well.The biggest problem was the spring on the tension roller when putting back together.But it just takes a little bit of patients and it was fine.Works great now.

Brought up repair video on my smart phone and followed instructions while doing the repair (pausing when needed) and completed the job in under an hour including vacuuming the lint from inside the dryer before re-assembly.

Unplug the dryer from out let, lift the lid (top of dryer), cut the zip tie. Pull the two wires and the plastec wireing harness apart. Remove the screws that holds the front panel on, and the screw and molded pice that holds the drum in place, remove the belt from around the drum. Now remove the drum, have to lift up and out on the drum. Remove motor, and pulley from old motor for use on new one. Put everything back together. Took me 15 to 30min to do this ( I recamend a new belt as long as you are this far and the price is a small amount for it. )

Took apart dryer and replaced limiter located on back, reassembled dryer and tested wiithout connecting to vent. Dryer working fine without vent connection. However as always something simple turns to disaster when children help. While cleaning out lint from dryer vent which I will say was the original problem causing the limiter to trip, youngest son wanted to help. Son did not know that to walk in an attic you must step on joists not drywall. No one was hurt just banged up falling into the garage. Extended repair to ceiling added dificulty factor of 2 days and a bit of insulation clean up. Good news is the dryer works fine and the vent is no longer clogged up with lint. Watch your help it always adds to the repair.

i folow the instructions from web page

Removed back panel, unplugged motor and released the belt. Remove top panel then front panel. Remove drum for better access. Vacuum the lint while everything is open. Remove old motor and replace with new motor. Reassemble. Suggest replacing the belt too.

Referred to Video and replaced drum support bearing as shown. Did not solve the problem as noise was still present. Called professional repairman, who replaced the belt pulley, along with all the parts I had just installed (came as part of a total kit). I was on the correct path, but just didn't go far enough to check out the belt pulley. If it should happen again, I could complete the whole repair process. Great learning process!!

The part fit perfect repair was simple thank guys for your help u are the best/removed the top/ front face /belt & drum removed old element installed new one dryer works perfect thanks again

Replaced everything on the dryer till I got the right problem, seriously, I now have a new dryer in an old body, still came out alot cheaper than buying a new one. I listened to every sound on youtube but none sounded like my dryer.

opened top of dryer, remove blown part and installed new part very easy.

I youtube'd the repair, and repaired it! While I was at it I replaced the belt! (Highly recommend replacing the belt while you are replacing the element!) Was a snap!

removed top-removed front-removed belt-removed drum (I didn't know how the drum came out WITH the bearing so I unscrewed the 3 middle screws on the back of the drum which released it from the bearing)- removed the bearing-that was when I knew what to order. installed the bearing on the drum before assembling all in reverse order. I wasn't sure how much grease to use so I used about 1/3 of it.

Had the drum bearing but had never got a round to putting it in we just let it squeek. Then the belt went. Easy enough, whatched the tutorial once and just did it. 35 minutes and back drying.

We followed the how-to video. It was actually easier than the video made it look. Our dryer had a removable panel behind the pulley to put the belt back on easier. We had to take the whole dryer apart, but it was not difficult at all. We replaced the heating element and put it back together. If you can screw a screw, you can do this repair. Our dryer is working good as new. I love this site!

As the clothes began to dry and got lighter the noise stopped. Apparently the noise was the result of the rear lower portion of the drum scraping the heater coil due to a well worn upper front felt seal. To repair; I watched a how-to-repair video that was posted on the internet and after watching it, everything was easy.