Models > AEQ6000ES1

AEQ6000ES1 Frigidaire Dryer - Overview

Get Parts and Repair Help for AEQ6000ES1

If you know the dryer repair part you need, you can browse the list of all parts on the AEQ6000ES1, or you can search by name or part description. You can also find your part by where it is located on the AEQ6000ES1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for AEQ6000ES1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$19.92

Rear Drum Bearing Kit

This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant and installation screws.

$8.61

Drum Belt

This 87-3/4" long dryer drum belt goes around the dryer drum and the pulley to rotate the drum once motor is activated.

$19.45

Drum Glide

Sold individually. 2 are required.

$2.77

Drum Support Bearing

$70.84

Heating Element Assembly

This dryer heating and housing assembly has terminals at four o'clock. This E-line assembly comes with a felt strip and insulators already attached.

$8.21

Thermal Limiter - Limit 220

This thermal fuse limiter, with a limit of 220 degrees Fahrenheit, is manufactured for both gas and electric clothes dryers. Once the internal temperature of the dryer reaches 220 degrees, the heating element cuts out.

$13.81

Lower Front Felt Seal with Adhesive

$23.71

Door Catch

$10.96

Lint Filter

This white dryer lint filter screen collects lint as it passes through the dryer vent.

$47.18

High Limit Thermostat

This high limit thermostat has a limit of 260 degrees Fahrenheit. Meaning that it will cut out when the internal dryer temperature reaches 260. This thermostat cuts back in when the temperature drops by 70 degrees Fahrenheit.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Loud Squeaking

  • Customer: Frank from Boyertown PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 245 of 253 people found this instruction helpful
1. Unplug dryer from outlet
2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs
3. Lift up top and tilt back out of your way
4. Unscrew two phillips scews on inside of front panel
5. Lift up and out the front panel. Two spring clips at bottom.
6. Rlease tension on drum belt at the motor. Acc... read more

short circuit with a brasier metal support

  • Customer: Juan Carlos from Weston FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 139 of 162 people found this instruction helpful
Disconect the dryer from the main power source.

1) Remove the two screws from the rear / upper panel (below the control panel).

2) Snap the front side using a flat head screw driver.

3) On the inside front, remove two screws (one on each side) from the upper side and snap the door assembly off.

4) Remove the rear m... read more

Motor would hum but not turn on when start knob was turned.

  • Customer: Elvis from Miami FL
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 135 of 155 people found this instruction helpful
The motor bearings had stiffened up – classic planned obsolescence.

I could tell the motor was bad, because when I tried to spin the drum by hand, it wouldn't turn in any direction. (Normally it can turn fairly easily.)

(Helpful hint: As you remove screws / parts, place them in a plastic baggie, and write on the baggie from whence t... read more