Models > AED4475TQ0 > Instructions

AED4475TQ0 Admiral Dryer - Instructions

All installation instructions for AED4475TQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the AED4475TQ0
496-510 of 809
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

dryer ran fine but the timer would not advance

  • Customer: Ronald from Philadelphia PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
removed rear cover of dryer (approx. 10 screws)and replaced cycling thermostat located near blower per easy instructions

No Heat

  • Customer: Lance from Compton CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The repair was made very simple with the help of Steve and his YouTube video instruction. I really can't take credit for the repair, my teenage son did it while I held the laptop and fed him the instructions. Clothes are dry, my wife is happy, so we're all happy and it cost less then $35.00.

the dryer was heating but the drum wasn't turning

  • Customer: DOROTHY from DINGMANFERRY PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watched the video on the computer and it was very easy to repair I had the dyer apart ,fixed and put together in about half hour

the lint chute assembly had corroded & would not accept the lint screen.

  • Customer: Richard from Paramount CA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I pulled thee dryer out from the wall, shut off the gas & disconnected the gas line & the air vent, I then removed the fasteners from the upper end of the lint chute assembly (accessible from the top of the machine). I then tipped the machine over on to its front side making the back fully accessible. After removing the back cover, I removed the remaining fasteners holding the lint chute assembly in place & removed the part. I then removed the assembly only to find that the seals were not included in the package even though I had specifically asked about the seal when I called in & place my order. The response to my question was " seals are included that is why it is called an assembly." The end result was that I had to use alternate material & fabricate my own seals in order to complete the installation. As a result a repair which should have taken no more that 30 minutes, took over two hours.

The drum would not tumble.

  • Customer: Renae from Hegins PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
We watched the video on the PARTS SELECT site and it was very helpful and I had no problem holding the flashlight for my husband!

Belt broke on dryer, drum therefore wouldn't tumble

  • Customer: Elaine from North Berwick ME
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Had a hard time at first trying to figure out how to place the pulley wheel that you place the belt around, it holds it in place so to speak, was getting very frustrated came upstairs went on line to your web site and lo & behold there was a video on how to do it, I watched that video (thanks Steve) and went back down cellar and had the belt on in less than 5 mins and everything is working fine. Thanks for all your help Dan

Off switch on door was broken.

  • Customer: David from Reisterstown MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video and did exactly what I was shown. Piece of cake. Thanks!

Dryer would not shut off

  • Customer: Les from Slinger WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I removed the top of the dryer and removed the faulty switch form it's mating connector. The simply removed two Phillips Head round headed screws with a screw driver and replaced the part all within 15 minutes. However, I also heard that it wasn't drying properly so after making sure my dryer vent was free of any lint build up, I removed the back of the dryer. Once removed, I completely cleand any dust from inside the dryer, then checked all of the visable wire connections and then went to PartSelect's fantastic web-site. Her they catagorize the top 7 reasons that could cause the problem (in my case) not drying and thenproceed to give you an idea of the most likely cause by publishing the failure rat in per centage values in decending order, they also provide schematics and the on top of all of that...they provide mini-videos not only showing you wher the parts are located but the step by step instructions on how to remove them and replace them. After all of this, I took my ohm meter and actually removed all of the 7 parts suggested, cleaned them up, ran a continuity check on each part and found them all in working order. Replaced the parts and checked the heat and it was back to normal!! There must have be a lose connection causing the problem. But, I can guarantee that the next time I have an appliance problem...I'll again be calling on PartSelect.com. They are awesom and they will be highly recommended to anyone I know that is experiencing problems. I have not ever seen a web-site that was so complete in excellent service. And there prices and shipping time speaks for itself. They are great!!

Belt on dryer drum broke

  • Customer: Thomas from Buffalo NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The repair on replacing the clothes dryer belt went great. Not only did Part Select send me the correct belt at a great price .. the helpful hints that other people gave was most helpful. The only glitch was when I was pushing the tensioner wheel to get the belt around the pulley it slipped and the spring came off. The instructions/tip of taking the drum out and how to replace it came in handy when I had to get the spring back into place. The belt finally went on but there was a slight twist in it by the tensioner wheel. Again the tip I got with my e-mail helped as I manually turned the drum and was able to right the belt. Kudos to the tips I received and the confidence I could do the job myself!!!!

WOULD NOT STOP WHEN DOOR WAS OPEN THEN WOULD NOT START

  • Customer: ruth from crosby TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
UNSCREWED BOLTS OFF BACK (2). TOOK DRYER VENT OUT UNSCREWED THE BOLTS (2) PUSHED TOP BACK AND LIFTED UP. OPEN DOOR UNSCREWED THE BOLTS (2) TO THE SAFETY SWITCH PULLED THE CONNECTION (WIRES) APART AND REPLACED WITH NEW SAFETY SWITCH.

drum not turning

  • Customer: Edward from Shrewsbury MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
push in on clips on front top at seams apx 2-3 inches from both sides. lift lid lean it back. remove door switch. remove front panel. remove old belt. replace with new belt lifting drum slightly to get around drum rib side down. reach in and push tensioner down to the left place belt around pully and over tensioner relase gently put all item back together.

Thermal CutOff broken

  • Customer: Lucien from Gainesville FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Tested the old thermal cut off with multimeter, and it was defective. Replaced it using the schematic provided.

Broken belt.

  • Customer: Cynthia from Mayfield NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Watched Youtube video first then followed directions included with belt. Very simple and easy to follow.

Dryer took a long time to dry clothes and towels,

  • Customer: Antony from Boone NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I viewed a number of vidieos on the Webb to determine the possible problems. The vidieos explained and demonstrated how to test the parts that could have been causing the problems. I tested the parts described in the vidieos and the ones I was able to test showed that they were not defective. I was unable to test the Cycling Thermostat and the High Limit Thermostat to my satisfaction so I ordered the two parts and installed them as demonstrated on the vidieos. The dryer works as if it was a new one. I am a very satisfied customer and will definitely purchase my parts from partselect.com in the future.

Dryer had no heat.

  • Customer: JOSEPH from Holliston MA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Took off the back panel removed old wires. Piggybacked new wire and put back together. The video was very helpful as far as where exactly to insert the new wire. Overall a very good experience. When it first happened my husband and I thought we would need a new dryer. We found your website and figured out what the problem most likely was. Ordeed the part it came within a few days. The money we saved not having to get a new dryer is great.
All Instructions for the AED4475TQ0
496-510 of 809