AED4475TQ0 Admiral Dryer - Instructions

since dryers are hard for me to determine. I used my OHMs meter to see that the Thermal Fuse was good. The door switch was good . The off on switch was bad.

After viewing a series of youtube videos on Kenmore Dryer repairs, I used a volt-ohmmeter to determine that the thermal cut off was the most likely part that had gone bad. I installed the new part that I had ordered from PartSelect and our dryer was fixed.

My husband and I followed the video step by step and it worked like a charm.

My Whirlpool washer/dryer combo is 15 years old and has given trouble-free service until this belt snapped. I went to the PartSelect website for the replacement part and found the instructional video. As a DIY neophyte I know my limits but this looked like something I could tackle and save a few bucks on. The part arrived pronto and installation went smooth as butta! I couldn't be happier and even the wife is impressed. Knowing what a service call would have cost makes the whole shebang even sweeter. Thank you PartSelect!

after the removal of the front i removed the drum and inspect all idler wheels for ware replace if needed. if not clean and lube. idlers must be in good condition...bad idler wheels can cause the belt to brake

Pulled the front of the dryer off. Removed the old belt. Replaced the new one by threading it flat side down, except for the drive motor which was ribbed, so the belt had to be installed sort of serpentine like. Replaced front of dryer and it's like new.

Removed two screws that allowed dryer lid to be opened up. That allowed access to door switch which was easily removed (two screws and disconnect switch). Replaced switch, closed lid and replaced two screws. Very east and quick.

The very first thing you want to do is Unplug the Dryer. I then took the two screws out that hold the lint screen to the top of the dryer. Then I used and old butter knife to pry the front top of the machine open. The top is held in place by two plastic clamps. Once I got the top loose I raise it up. Once I had it raised, I pulled up and out on the front panel where the dryer door is. I left the door switch connected and just put the panel off to the right. I then removed the old belt which was lying under the drum. The drum does drop slightly once you take the door off. This was one of the hardest part of the project for me as I did not have any help. This would be much easier if you just have one other person to hold the drum. Anyway, I then placed the new belt around the drum and used my left shoulder / arm to hold up the drum while feeding the belt in the slot on the tensioner and then over the dryer motor pulley. Make sure you don't twist the belt. I originally had a twist and when I hand turned the drum the belt came off the pulley and the tensioner. I had to rethread the belt through the slot on the pulley and then put the belt back on the dryer motor pulley. I then gave the drum a couple complete turns to make sure everything was staying in place. The tensioner on my dryer did not look like the instructions that came with the new belt. My belt tensioner is like a half circle and the belt just rides on it. I think if I had it to do over I would have purchased a new tensioner also. I feel that the belts constant motion against the tensioner probably causes it to wear out faster. Once I made sure evrything was staying on I replaced the front panel that has the door. You just slide the bottom into the slots while holding up on the drum so it lies on the felt padding around the door. Replace all screws and presto. Works like a new Dryer. Make sure you don't forget to plug it back in... Overall it's a pretty easy fix and much less expensive then a service call or purchasing a new Dryer.

I ordered the thermostat switch thinking I'd isolated the problem. Discovering that wasn't the problem, I disconnected and inspected the heater coils and found the break in the coil. I then ordered the heater element (also from Partselect.com). It was simple, fast and works like a champ. I did discover my outside vent had a bird's nest in it. You really need to occasionally check your dryer vent (inside and out), for lint and apparently bird's nests.

Maytag makes it really easy to replace this part. Unlike the video which has the access panel in the rear of the dryer, Maytag accesses all the thermostats and wiring front the front so you don't even have to pull the unit away from the wall. Smart!! The video was great to show you what the part looks like and how its installed. Installed the part in less than 10 minutes. Now our clothes are drying as they should in half the time...best $20 I spent in a while.

Had to take 2 screws out of the lint box.Lifted the dryer top and in 3 minutes I was done.I buy all my parts from partselect.A while back I replaced a thermastst in my refrigarator.They even have videos on here to show you if you never work on things befor.

Watched Video a couple of times,,, then took off the back Panel, located the sensors, removed the Heater Coil to examine, for any breaks, looked OK, then replaces the 2 Sensors in the Thermal Cut-Off Kit, Finally Cut off and replace 2 Terminals needed to adapt wiring. Re-installed back Panel. Overall, took about an Hour Oh, it "worked" Dryer repair was successful

Popped the left and right side clips that hold the top, took out left and right side screws that held front face on, disconnected the wire that went to the door, tilted the door to me and lifted up from tabs on bottom. The old belt was broke, so it was easy to get off. Put the new belt on the drum making sure that the rubber ribs were touching the drum then I put the belt on the tensioner pully and motor pully. I rotated the drum by hand at least 1 full revolution to make sure that the belt was on right and it wasn't twisted, then I put everything back together. Easy 10 minute job... Art

I watched the installation video. It was exactly as shown.

I watched the wonderful you tube video, and realized my whirlpool dryer was a bit different than the one used as an example. I first unplugged my dryer. I didn't need the putty knife because I had to take the sides off the top part of dryer that housed all the wires. I just needed a small Phillips head screwdriver for that. There were three screws holding the top of the dryer down, and i took those off with a small socket. Then I just slid the top of the dryer forward, took the top completely off, and there was the door switch on the upper left side. I unscrewed the switch from the dryer because I couldn't get it apart until I did. That was the hardest part of the whole process--pullining the switch apart. I used a flat head screwdriver and pliers to help separate it. At that point, I went online and ordered the door switch from Part Select. I received my part within two days. I put the new switch in, and it worked great--my dryer light also came back on when the new switch was installed. This is the first time I have ever attempted anything like this, but after seeing the video, I felt like I could do it. Just for the record...I am a female and 65!