AED4470TQ0 Admiral Dryer - Instructions

The video from your website is exactly the steps I followed to remove the old door switch 3 wire and install the new one. Very easy! NOTE: 1 Week before the dryer totally stopped working, my mother opened the dryer door when it finished (sound alert) but, the dryer was still spinning + the light did not come on. I noticed that the small black lever (part of the door switch wire which sticks out & presses against the door when the door is closed) was extremely loose. It seemed as if the lever was broken (perhaps the last time I used the dryer the door slipped from my hand and broke the black piece). Video tutorial was great!

I watched a video from Parts Select and learned that most problems with gas dryers revolve around two things: a broken door switch and a burnt fuse. I knew my door switch was broken. So I figured out how to lift the top of the dryer (unscrew two bolts in the back and two screws under the lint screen) and pry the hood open.) The switch was right there, held in place by two screws in the door frame. I received the part I ordered the next day, on the simple ground delivery. I replaced the door switch, closed the lid, tighten everything down. Problem solved for $15!

Remove Lint filter remove two screws that hold lint trap to top of dryer.Use putty knife to push on two top clips that hold top of dryer down on body of dryer.Lift top and locate door wire that go to switch,romove two screws that hold switch unplug three prong connector plug in new switch and reverse disassembly instructions.

I followed video instructions. Raised the top, slipped off the front, installed the belt, aligned, installed tension part, reinstalled front, lowered the top and inserted lint trap. Job done. Quick and easy. The video was the key to the whole project.

This was my first dryer repair. The only difficulty I had was figuring out how the belt tensioner was set up with the belt. The old belt broke so I didn't know how it was suppose to work. Anyway, it took a few minute to figure out that one end of the bracket was a "spring" that allowed it to flex a long ways! Pretty easy job.

ordered the part recived the parts and installed the part that easy. saved us lots of money did not have to buy a new dryer.

I thought I would do it myself and figured that because it wasn't heating I would replace all the thermostats and thermal fuse. Because I wanted to get it going right away, I also ordered a timer just incase. Turns out it was the timer and not the thermostats or fuze. I have a virtually new dryer again. Replacing the parts was really easy and didn't take long. Word of advise is to use an electrical (ohm) tester to determine which part is faulty; this will also save money by not buying not-needed parts.

I followed exactly the video. It really was that simple. My 5 year old even helped me unscrew the nuts. The Thermostat was on the lint shaft and unscrewed easily. Once out I removed the wires. The hardest part was removing the wires, They were really tight. I replaced the wires and screwed in the part. Before I replaced the back I cleaned out the lint tube and turned on the dryer. I saw the flame and the heater kicked right on. I replaced the back and was done. *****However the next time the dryer went the heat didn't remain on and turned off too soon. I did some more research and found you usually need to replace the thermal fuse at the same time on Whirlpool units. So I have ordered the part and will let you know if kept the heater from turning off too soon.

(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple to get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.

The video you had of my dryer was different then my dryer and the pulley was in the middle of the bottom and the motor and fan were in front of it. I had to replace the belt without being able to see what I was doing. I couldn't get it at first then realized there was tension on the pulley wheel and had to pull it towards the other wheel in order to get the belt on there. Once I pulled the wheel it went on really easy. My first time working on a dryer but I knew I could do it myself.

instructions were clear and repair was easy

Well, to Figure the issue I took the entire thing apart. Actually a lot more than needed. I found the torn belt and ordered it. I did not realize I may need a new belt tensioner which is sold with a wheel for the belt to wrap around and be tensioned by. Actually the original just utilized a rubber c or u shaped design(no wheel) for the belt to slide over. Anyways, instead of ordering and waiting for a new wheeled belt tensioner, I installed new belt with all original parts and working fine. I did oil up the drum rollers to reduce noise. And since I took the whole thing apart I cleaned the lint from every place it could hide. Ps a coke can is said to be helpful to hold the drum up while installing the belt but I found a jug of laundry detergent did better. Totally easy project for someone with no appliance repair history

The broken belt was found when I opened the dryer. The part number was on the belt and a quick online search led me to PartSelect. The part was available, delivered in less than 2 days and there was an online video showing the entire repair in detail.

My ground wire in my electrical box was not connected.

Un plug the Elect. The two screws that hold the lent screen in place and the top. I took them out and I used a putty knife to open the top of the dry. un plug the switch And take out the two screws under the switch. That was all too it. Just like the instructor said .