Models > AED4370TQ0 Maytag > Instructions

AED4370TQ0 Admiral Dryer - Instructions

All installation instructions for AED4370TQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the AED4370TQ0
616-628 of 628
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broken dryer belt

  • Customer: joe from partlow VA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Thousand dollars for a new dryer or twenty bucks for a new belt. Thank-you parts select. Ordering was easy and the instructions were bang on!

Dryer would not run

  • Customer: Joe from Harrisburg PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Motor was tight, very hard to turn by hand. take the back motor mount strap off and you will be able to put an adjustable wrench on the shaft of the blower. you should be able to put vice grips on the pulley end and turn motor counter clock wise (CCW) to let handle of vice grips rest against the bottom of the machine and turn adjustable wrench CCW to turn off blower wheel. However, the one I did, the wheel was so tight I ended up having to break the blower wheel down small enough so I could pull the motor out. remove the front motor mount strap and pull the motor out. Install the new motor wheel and motor in the revers order. Set motor in place, install front motor mount strap, put blower wheel in from the back of the machine and start treading on the motor shaft. Then,from the front, tighten the blower with wrenches turning clock wise and put machine back together. Always unplug machine whenever working on it. If you go to Whirlpool web site there is a step by step video that will walk you through this entire process.

Dryer was not putting out any heat. Clothes were still wet after completing a full cycle

  • Customer: Sandra from Albuquerque NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I checked all of the most commonly affected parts (as described on this site) with an ohmmeter (My first time but very easy to use). The only exception was the heating coil but this appeared to be working fine. The cycling thermostat showed resistance so I ordered a new one here. Replaced it and now the drying is working like new! The informational youtubes, diagnosis, purchase and repair only took me an hour. Never tried fixing an appliance myself before but so satisfying! $25 dollars and convenient timing is much better than the $350 I spent to have an appliance repairman fix my washer.

broken belt

  • Customer: HUNG from KENT WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
follow video and fix.

The dryer was making a terrible sound and it stopped turning.

  • Customer: Cindy from Pelzer, SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
I lifted the top of the dryer. I unhooked the hangers from the door and took it off. I pulled the drum out, took the broken belt off, slid the new one around the outside middle of the drum, turning the rib side of the belt out,and ran the belt through the pulley attached to the bottom base of the dryer (tension pulley, right hand side), slid the drum back inside the dryer frame, reattached the door, closed and snapped the dryer lid and it worked great!!

on-off switch

  • Customer: vincent from lesterville MO
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
took off the back part with nut driver removed switch assembly by pressing down with a little pressure and it snapped out the new was a little different but worked on installing this was an easy assembly. just do things in reverse when finished just plug in electric and push switch to turn on. very easy to install.

Ancient Kenmore Dryer

  • Customer: Franklin from Eureka CA
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Your customer service was great, but your video wasn't particularly helpful because of the extreme age of my dryer. For one thing, with these really old dryers, you don't have to slide the drum out at all; you just unscrew the front panel and slip the belt in that way. The printed diagram that came with the belt helped me figure how the belt slips through the pulley assembly, but the drawing could have been more clear. In spite of my bickering, I probably saved $50 fixing it myself.

Drum not turning.....broken drive belt

  • Customer: Ashby's from Foster WV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Disconnect electric power, the top & cabinet are connected by 2 reusable locks about 4 inches from each front corner, use a thin flat putty knife or similar object, push inward on a lock while lifting gently on the front of the top piece, then let the top rest against the wall. ( a wire on each end of a safety switch for the dryer door may need disconnected) Remove a screw from each front corner of the cabinet, then pull upward on the loose front panel to access the drive motor, remove old belt. install new belt by lifting the front of the drum just high enough to allow the new belt, place groves of belt against the drum and around the motor pulley and belt tensioner, re-install cabinet front, (re-connect safety switch wires) return top and push down at cabinet locks.

broken belt

  • Customer: Joy from livingston LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
It was really easy I watched your video on how to do it the video went step by step and was very helpful

changed out motor

  • Customer: JEFFERY from KENNER LA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
followed video on line

Broken Belt

  • Customer: Jeffrey from Bensalem PA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watch the video you sent me, and every thing fell into place

Dryer was getting too hot.

  • Customer: Kenneth from Shady Spring WV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I reviewed the on-line video (which was very good by the way) and read the instructions that came with the thermal cut-off kit. Replacement of the upper thermostat was a piece of cake, very straight-forward; just remove the old & replace with the new. The instructions for replacing the lower thermostat were a little confusing because my dryer did not have the orange wire coming from the wiring harness, but after looking carefully at the old thermostat and how it was connected, I finally figured out how the jumper wire was to be connected and successfully installed the lower unit. Bottom line...the dryer works like new. Much cheaper than calling the repairman! Thanks PartSelect!

REPLACE DRIVE BELT

  • Customer: William from Marlborough CT
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
What a pain in the butt to route the belt thru the tensioner! There's room for only one hand in there. The guys who do this for a living must have some secret. My solution was to drill a 3/16 hole thru the side, make a J-hook from 8-32 threaded rod, use that and a wing nut to pre-load the tensioner, route the belt, then slowly back off the wing nut until the belt was tight. It works....
All Instructions for the AED4370TQ0
616-628 of 628