Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ADG9000AWW

ADG9000AWW Admiral Dryer - Overview

Get Parts and Repair Help for ADG9000AWW

If you know the dryer repair part you need, you can browse the list of all parts on the ADG9000AWW, or you can search by name or part description. You can also find your part by where it is located on the ADG9000AWW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for ADG9000AWW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$14.56

Multi Rib Belt - 92-1/4"

This multi rib belt is an important part in your dryer, it is what helps rotate the drum. The belt attaches to the drum, idler pulley, and motor pulley. As the armature of the moto...

Order within the next 7 hrs and your part ships today!
$21.97

'M' Series New Style Coil Kit

This is an M series new style coil kit, used in gas dryers. When the igniter reaches a high enough temperature, these coils work together to let the gas enter the dryer. The coils open the gas valve; if the valve does not open the heating element will not ignite. Both coils must be operational for the valve to open. This is a safety mechanism to ensure that there are no unsafe buildups of gas inside your appliance. This kit comes with a three-terminal boost/hold coil, and a two-terminal main coil. Each part is approximately 1 1/4 inches in diameter. If the igniter glows but shuts off without igniting gas, it means one of both of your valves is faulty. We recommend you replace these as a set. Before you begin this repair unplug your appliance and shut off the gas supply.

Order within the next 7 hrs and your part ships today!
$27.70

Radiant Flame Sensor

If your gas dryer is not heating up or igniting, then replacing the flame sensor, located in the burner assembly, could solve it. This part senses heat from the igniter to monitor...

Order within the next 7 hrs and your part ships today!
$13.74

Lint Filter

This is an OEM lint filter for a dryer. This lint filter screen has two side guides on either of the screen. One measures 3/8 of an inch wide, while the other measures 5/8 of an inch wide. This part is white and is made of plastic. You may need to replace the filter if the plastic is broken or warped. Simply slide the lint filter out of the slot and slide the replacement filter in. The lint filter collects lint from drying clothes and prevents lint from building up in internal moving parts, specifically the heating coil. Neglecting to clean your lint filter is a fire hazard, be sure to clean it on a regular basis.

Order within the next 7 hrs and your part ships today!
$14.78

Door Catch Kit

This door catch kit is designed for use in dryers. This is an authentic OEM replacement part. This catch assembly ensures the door of your appliance will close, and remain closed. ...

Order within the next 7 hrs and your part ships today!
$43.08

Blower Wheel

This wheel has a deep D-shaped shaft receptacle. The spring clamp is not included with this part.

Order within the next 7 hrs and your part ships today!
$16.18

Rear Drum Support Roller

This rear drum support roller stabilizes the dryer drum and holds it in place during the drying cycle while the drum rotates on the support wheels. If your dryer is making loud squ...

Order within the next 7 hrs and your part ships today!
$34.15

Motor Pulley

Order within the next 7 hrs and your part ships today!
$5.81

Blower Wheel Clamp

This blower wheel clamp, used in a clothes dryer, is a clamp that holds the blower wheel to the motor shaft. This part helps hold the blower wheel in place to function easily and p...

Order within the next 7 hrs and your part ships today!
$18.18

Drum Felt Seal

The drum felt seal, used in dryers, allows the drum to smoothly glide with minimal friction. If any of the following symptoms occur with your dryer, replacing the felt seal can be a solution to your problem: makes noises, does not tumble, takes too long to dry, not enough heat, or no heat at all. First take off the front panel of the dryer and remove the drum. Next, unscrew the old drum support wheels by following the instructions from the manufacturer manual. To get the retaining clips on, place them in front of the wheel shaft and clamp down on the clip and shaft as you snap it in. This part can be used for both the front and rear in some models. Remember to unplug your dryer from the power source before beginning this project.

Order within the next 7 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

lint filter broke

  • Customer: Jane from Grand Forks, ND
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 468 of 476 people found this instruction helpful
I pulled out the broken lint filter and put the new one back in, real easy. I am so happy with the prompt delivery I got from PartsSelect.com. I ordered on a Monday and and it was delivered on a Wednesday read more

No Heat

  • Customer: Stan from Riverside, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 373 of 381 people found this instruction helpful
Lift the top. Remove (2) screws holding the front of the dryer in place. Lift the front off the 2 retaining clips on the bottom of the dryer. The hardest part of the install was removing and replacing the igniter. A couple of helping hands from the girlfriend to hold the parts in place while I replaced the two screws was very helpfull. Installing the mu... read more

Dryer ran but would not heat

  • Customer: Gary from Haverhill, NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 307 of 344 people found this instruction helpful
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are located on top of t... read more