Models > ADG7005AWW > Instructions

ADG7005AWW Admiral Dryer - Instructions

All installation instructions for ADG7005AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ADG7005AWW
31-45 of 398
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broken belt and idler pully

  • Customer: George from Haverhill MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench set
  • 7 of 7 people found this instruction helpful
Remove front pannel
remove wires to light and switch
remove drum panel
disconnect motor wiring
unscrew motor mount
replace idlerlever replace belt reassemble all parts

broken plastic vent

  • Customer: joe from Beacon Falls CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 7 of 8 people found this instruction helpful
I am not mechanical so if I can do it so can. UNPLUG THE DRYER FIRST!There are two bolts on the back of the dryer that connect the control panel and the dryer itself remove these and take out the brackets that are held by these two bolts, I used a socket, lift up and peek in to the front top you will see two screws that hold the other side of the top of the dryer lower the back side and move to the front of the dryer now that the back bolts are removed. Take a large screwdriver and place a dishrag or handkerchief so the flat side is inserted where these screws are located{preventing scratches}pry upward it will seperate the top of the dryer from the front of the dryer move over to the next screw and repeat now the top is loose and can be slid backwards until there is room for you to see down in front of the dryer, notice there are three wires that connect for the light on the right hand side, take the time to write down there color and in what order they are located as you will have to remove these now inside the front panel from the top about a third of the way are two bolts, one on the left and one on the right use the socket to remove these now pull the front panel to you and lift up, the front panel will now come off set aside. remove the three screws that attach the plastic vent from inside the dryer,pull out plastic vent, vacuum out dust and lint install new plastic vent install the three screws from inside the dryer drum and reverse the process you are finished!

very noisey dryer

  • Customer: Mike from El Granada CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 7 of 8 people found this instruction helpful
Open bottom panel and observed back left drum roller wheel wobbling and obviously making the loud rumbling banging sound. Search goggle for Amana model part -- found, and read the list of other DIYs:

Take off the lower and upper front panels (two screws

Remove the front drum glide holder (four screws. Careful
here because of the two wires to be removed for
door open off switch;

Pulling drum forward only enough so the bad roller wheel
would come off shaft after removing shaft snap ring

Grease new roller hole and old shaft then place the
new wheel roller on shaft;

Replace all items back after cleaning lent off.

Note: Snap ring was a bit tricky (need snap ring pliers)--make sure it is clipped back all the way on the shaft after new wheel is installed. Also, I thought it was a good idea to put something underneath the dryer drum to support it while it was slightly pulled out -- a block of wood, etc. I found a spot remover plastic bottle that wedged up to support the dryer drum enough to take pressure off the belt during wheel replacement.

Door Catch was broken

  • Customer: Inocencio from Edinburg TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 8 people found this instruction helpful
I just inserted the door catch, which by the way fit in perfectly. Thanks. Took 5 seconds to repair.

Idler wheel was making a screeching noise

  • Customer: John from Derry NH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 7 of 8 people found this instruction helpful
I first thought the drum rollers were the source and replaced those. It took me 60 minutes to get the dryer disassembled and wires labeled for reassembly the first time. Knowing how to do it for this repair made everything go quicker.
I removed the tension from the belt by pulling it away from the spring and then slipped the belt off the motor. I then removed the drum from the dryer to get to the idler arm assy.
The trickest part of this repair was putting a box wrench on the nut on the motor side of the frame. I found a 3/8" box wrench with an angled handle that worked well. I then used a 7/16" socket on the other side of the idler arm base and removed the bolt. I was careful to note the position of the tension spring so that I could put it back together correctly. I then put the new idler arm assy in place with the bolt through the frame but had some trouble keeping the nut in the box wrench. I ended up using a bit of chewing gum to keep the nut in the box wrench long enough to get it threaded!

From there it was a cinch - just put the belt back around the drum, the idler wheel and then pulled up on the arm while I slipped the belt over the motor. No more screeching!

Broken plastic screen (on frame that holds wire lint screen)

  • Customer: Karen from Homer Glen IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 9 people found this instruction helpful
Removed bottom door panel, four screws. The new part was a slightly different (looks like improved) part, so only had to put two screws back in. Very simple. The only reason it took more than 15 minutes was because I cleaned exposed areas while the panel was off.

Dryer making a lot of noise and clothes were getting very hot

  • Customer: MedPro from Crest Hill IL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Wrench set, Wrench(Adjustable)
  • 7 of 9 people found this instruction helpful
Remove the 2 screws at bottom of front panel, remove lower panel. Then remove the two screws at bottom of front door. Lift door forward so spring hooks can disengage from the top panel. remove door, disconnect the 5 wires to the door latch and light. remove the two screws at top of dryer to lift up top panel. Remove 4 screws at the front holding the drum. Disengage the belt from the tension pulley and remove drum. Replaced both roller wheels at the rear of the drum( one was broke). Then remove the screws (about 6 holding the plate in front of the blower wheel. Use a wrench to hold the nut at the back of the motor and a scocket wrench to remove blower wheel. (The Blower wheel was broken from the shaft and was spinning freely). Then do it all backwards to re assemble. i spent more time cleaning the lint from the inside than I took making the repair!

Door safety switch would not close keeping dryer from running

  • Customer: John from Warsaw IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 10 people found this instruction helpful
Shut off or unplugged dryer for safety.

Slipped thin blade putty knife up under bezel of switch to unlatch from the panel and pulled forward to remove the swwitch from the dryer. Unplugged the quick connect terminals (3) from the old switch and plugged them onto the new switch. one of the terminals had gotten quite hot and darkened the insulation so it was replaced with one that was supplied with the switch. that was a cut, strip, crimp process. Placed the new switch into the panel and snapped into place.

replacing broken lint filter

  • Customer: Paula from Lawrenceburg KY
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
Ordered new lint filter, which did not quite fit. Called company and was told that filter had been redesigned to remove the felt surround, and that sometimes the new filters did not seat well. It turned out that the exhaust pipe was filled with packed-down lint causing the new filter not to go all the way into the slot. My husband surmised that that was why the first filter broke because volunteers at the Humane Society adoption center were trying to shove the filter into a groove that no longer worked. He took off the top, the front, and one other piece before removing all of the lint he could reach. Once that was done, the filter fit fine.

rumble from drum, hard vibration from drum

  • Customer: Christopher from Severn MD
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 5 of 5 people found this instruction helpful
The parts to replace were mounted to the rear wall of the dryer and only the front pane is removeable. With the panel removed the drum had to be pulled carefully straight out. The belt and tention arm were difficult to reposition. Since you have the appliance apart replace both roller and roller support brackets one of which you cannot see from the front. Throughly vaccum all lint and roller wheel debris . If you have an air compressor take the time to blow out the motor . Make sure to rig a device to hold the tention arm back with the belt correctly aligned while sliding the drum back into place. PARTSLECT is great , easy to use and suggests other parts I may not have thought of and quick . Parts were here in 2 days standard shipping. I was in the dog house for putting this off too long. My wife is happy so I'm happy.

The dryer started making terrible noises.

  • Customer: Caroline from Rockland ME
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
First I went to thinking it was best to go to the manufacturer for parts. Their search engine did not even recognize my part number. I tried every way I could think of. Then I just entered the model number in google and it sent me to the website. Diagrams came up and I chose parts from the pictures. The parts arrived in about 3 or 4 days and fit perfectly.

Dryer squeaked while running

  • Customer: Robert from Kellogg IA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 5 of 6 people found this instruction helpful
Replaced the recommended drum rollers, belt and tensioner, light bulb. Found repair manual online (bit of a hunt)made job easier still took 2.5 hrs. Then turned drum by hand no squeak. Turned it on and still squeaked. Isolated to motor. Replaced it (had to take dryer completely apart again but went quicker due to experience also had to disassemble the motor assy and rebuild. Took 1.5 hrs works like new now. The design of the dryer is not bad remove bottom front panel first, screws at very bottom of panel then two more screws are uncovered to remove front. It just lifts up and pulls out. then remove four bolts which hold front frame on (supports drum) all this has to be done to reach the replacement parts. drum wheels are held on by snap rings not the screws (real fun if you take them out) reverse to reassemble.

High pitch rubbing noise from dryer when operating.

  • Customer: Harry from Las Cruces NM
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 5 of 6 people found this instruction helpful
1. Disconnect power and hose. Use a putty knife to release top of dryer. Two restraints couple inches in from each side on front. Raise top and do not remove. Block it up in vertical so it doesn't fly down to back.
2. Disconnect five wires at front. Use magic marker to mark re-installation instructions on underside of top.
2. Remove metal screws (2) that hold front to frame. Remove front.
3. Pull dryer forward and put cardboard box, or some such thing under back to support when laying dryer down.
4. Remove frame (4 screws) that supports filter assy and front of drum.
5. Remove belt. Mark assy. sequence on underside of top.
6. Remove drum.
7. Stand dryer back to upright position.
8. Disconnect spring from idler lever. Drop light may help here. Note position of lever for re-install of new.
9. Unscrew bolt that holds idler lever. Nut is on back of bracket. Must re-install this way as bolt has pivot surface for lever on front side.
10. Install new lever and reconnect spring.
11. Lay dryer back on box.
12. Put drum back in place. Insure it seats well all around the felt gasket. Any misalignment here and it will not rotate smoothly.
13. Put belt around drum using small pieces of tape to hold it into position around drum, and them depress the idler lever and install belt around motor pulley. Rotate drum to insure it rotates smoothly. Remove tape.
14. Re-install filter bracket and insure drum seats nicely in felt gasket. Again, rotate to insure smooth operation.
15. Pull dryer back to standing position and reinstall the front, and re-connect the wires.
16. Lower top and push down to reconnect locking devices.
17. Plug in dryer and turn on to see if all is well.
18. Re-install hose and start drying all those clothes.

Noisy and not drying the clothes

  • Customer: Pietro from Fairfax VA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set, Wrench(Adjustable)
  • 5 of 6 people found this instruction helpful
This was my first time repairing a dryer. If I knew when I started the project what I know now, it would have been an easy repair. First, you should know that the series number (used for selecting a wiring diagram) is the last two digits of the unit's serial number (not model number). In my case, the series number was 11. The hardest part for me was figuring out how to take the dryer apart. I made the mistake of starting with the top instead of the front. In fact, I removed the control panel and disconnected all the wires, labeling them carefully, and creating a diagram, so i could put it all back together later. I now realize I could have left that all together and just lifted the top up in the front without removing it. That knowledge would have saved hours of work, so I hope it helps someone (prop up the front a few inches and start by removing the panel on the lower front, then remove the screws on the main front panel, and then pull out the bottom of that panel toward you until the top of that front panel disengages from the top of the dryer - the rest is obvious). So it turns out there were two separate problems: 1) the blower wheel had broken completely off of the motor so it wasn't spinning - this is why hot air wasn't being pulled through from the heater in the back of the dryer; 2) the pulley on the spring-loaded lever arm attached to the motor was squeaking due to lack of lubricant. So the solution was to replace the blower wheel and spray WD-40 in the pulley (and also, for good measure in the roller bearings that support the drum in the back of the dryer). Most of the time spent on the repair was just due to my own mistakes. In particular, once I got everything back together after the repair, it stopped squeaking and there was good airflow, but it wasn't heating. I spent an entire day trying to troubleshoot the lack of heat. I tested and bypassed all of the thermostats and heater fuses and the heating element still wouldn't come on. I even managed to accidentally ground one of the leads from the fuse and had to replace a melted wire connector (trip to the Shack). In the end, it turned out that a wire which had been accidentally disconnected from the main power cord to the dryer, I had put back in the wrong spot. There is L1, L2, and neutral going into the dryer. I had the heater on the same circuit as the motor and other stuff. Once I traced the wiring diagram back, I realized this and corrected it by putting the heating circuit back onto L2. Now it "hums like a Singer". If everything had gone smoothly, instead of being a 2-day repair, it would have been a 2 hour repair. 2 hours instead of 1 because to get the leverage I needed to remove the old blower nut, I had to actually pull the motor assembly out of the dryer and move it to my workbench. Someone who is strong or more limber or has better tools might be able to skip that step, reducing the time by about 45 minutes. Good luck!

old latch broke

  • Customer: Jim from Germantown WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 6 of 9 people found this instruction helpful
I inserted the clip
All Instructions for the ADG7005AWW
31-45 of 398