Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ADG20L2H

ADG20L2H Admiral Dryer - Overview

Get Parts and Repair Help for ADG20L2H

If you know the dryer repair part you need, you can browse the list of all parts on the ADG20L2H, or you can search by name or part description. You can also find your part by where it is located on the ADG20L2H by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for ADG20L2H parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$21.99

'M' Series New Style Coil Kit

This is an M series new style coil kit, used in gas dryers. When the igniter reaches a high enough temperature, these coils work together to let the gas enter the dryer. The coils ...

$15.68

High Limit Kit

The high limit kit comes with three separate thermal fuses for dryers. One electric thermal fuse with a limit of 258, one gas high limit at 240, and one gas and electric high limit thermostat with a limit at 300. The thermal fuse kit shuts off the motor in the dryer when it begins to overheat. If the dryer will not heat, is overheated, shuts off too soon, or takes too long to dry then the thermal fuse might have exploded and need to be replaced. For replacement instructions refer to the diagram by manufacturer. For safety, unplug the dryer before installing the part.

$27.70

Radiant Flame Sensor

If your gas dryer is not heating up or igniting, then replacing the flame sensor, located in the burner assembly, could solve it. This part senses heat from the igniter to monitor...

$16.18

Rear Drum Support Roller

This rear drum support roller stabilizes the dryer drum and holds it in place during the drying cycle while the drum rotates on the support wheels. If your dryer is making loud squeaking or thumping noises, or the dryer will not tumble, there could be an issue with your rear drum support roller. If you can see that the roller is damaged, you should replace it right away. The repair is relatively easy, and takes between 15 minutes and 1 hour to complete. This drum support roller works with electric or gas clothes dryers, is sold individually, has an outside diameter of about three inches, and comes with a bearing.

$5.81

Blower Wheel Clamp

This blower wheel clamp, used in a clothes dryer, is a clamp that holds the blower wheel to the motor shaft. This part helps hold the blower wheel in place to function easily and p...

$3.02

Screw

This screw is sold individually.

$24.06

Igniter with Wire Harness

This part lights the gas burner to create heat.

$43.86

Front Glide Kit

This kit includes 2 glides (left and right), 2 pads with adhesive backing and 1 support brace.

$12.05

Drum Glide and Cushion Kit

Pad has adhesive backing.

$5.96

Retaining Ring

This retaining ring is well under an inch long. Made entirely of metal, this ring is intended for use with some clothes dryers.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer ran but would not heat

  • Customer: Gary from Haverhill, NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 311 of 348 people found this instruction helpful
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are located on top of t... read more

Electric dryer would not heat - Thermal fuses - $25 fix - I love DIY

  • Customer: Ronald from Fredericksburg, VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 185 of 202 people found this instruction helpful
1. Unplug dryer from power outlet
2. Lift dryer top from front (hinged in rear). Just friction holding top down. Use flat scewdriver wrapped in cloth to help lift.
3. Locate heating element - rear top behind drum
4. Unplug red wires to the high limit thermal fuse
5. Unplug red wires to the heating element
6. Unlug white wires to the ... read more

Timer wasn't working (New Timer)

  • Customer: Joaquin from Las Vegas, NV
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 136 of 77 people found this instruction helpful
Timer wasn't working on the regular cycle so I replace it with a new one from partselect. It still wasn't working so I ordered and replace the cycling thermostat, the thermal fuse I also cleaned the vent and dryer it still didn't work so I read the diagram for the electrical and found that a coil for the gas valve is line with timer. I ordered the coils for ... read more