ADG20L1W Admiral Dryer - Instructions

Followed the parts select You tube video. Was helpful. Note the Ignitor kit is very sensitive. We didn't need an ignitor right now but purchased one in case the other 2 parts didn't help the problem. We took the ignitor ( wrapped in a bag) out of the packaging and it snapped in half without even touching the sensitive end. Note handle with extreme care.

Went online to see if this was a common problem... found the Part Select site... watched the short repair video... thought I could give it that a try, if it worked I just saved $150.00 bucks! Sent for parts, got them in two days! The repair was quick. I bought a nutdriver for the task but it wasn't a magnetic bit...get a magnetic nutdriver! Those small screws can get away from you. I had to slowly unscrew the screws and catch them with a telescopic magnet. I was washing a load during the dryer repair in hopes the repair worked..it did and I(Mr.Mom)completed 4 loads that morning.

Less than a houre

Un plug dryer . Take off dryer door . Remove front panel by pulling out. Remove 2 screws holding coil bracket . Remove electrical connectors ,remove 2 coils . Install 2 new coils same as old ones connect elect. Wires replace coil holding bkt. Unplug flame sensor . Remove 1 screw . Replace old flame sensor with new plugin elect. Connector replace in reverse wala ,,,alldone button up dryer plug in dryer . . Good to go.

Repair was easy, remove bottom cover, remove screws that hold coil bracket, remove old coils & slip new ones on & button up. Dryer works fine now.Had the new parts within 3 days. Thanks PartSelect!

The part came in very quickly. If you know how to remove the front panel, it is very easy to repair. The hard part is to diagnose the problem. The first thing to check is the igniter. If it comes on then you look for faulty limit switches. If you have lots of training in electronics and appliance repair this is very easy, if you do not I would not try this. I have 40 years in the repair business, It still took me 1hr. to find the problem. the switch was intermitted, one time the dryer would work the next time it would not. Good luck and happy repairs.

Pushed in the Door Catch, and it was fixed.

Unplug. Remove door and front panel. Unplug two coils. Remove one screw and loosen other on bracket holding coils in place. Slide off coils and replace ( take note one has terminals up and one down). Reassemble.

First I stumbled around on my own trying to figure out the problem then I remembered PartSelect & the info I got to fix the dishwasher. The info given for the dryer pointed to 2 main problems for no heat, tested them with the Ohm meter & ordered the part. We have a dryer again !!

My father and I were deciding on weather or not to purchase a new stove. The stove had always worked well but one of the front burners would not work and the broiler element was cracked in half. I thought I could fix it and save alot of money and not have to purchase a new one. I entered the model # into the search engine from parts select, alot of discontinued parts came up that were unavailable. I then went to search by product and narrowed the selection to brand,size,metal,and category such as electrical. I was given like models that have these parts in common. I was surprised how many parts were available for my stove. I had originaly bought the unit through Montgomery Ward. Admiral, Maytag, and Whirlpool share many of the same parts. From the photos and descriptions I was able to find the correct parts. I purchased a new burner element and a broiler element. Unplug the stove first. The tools needed were a Phillips screwdriver and believe it or not that is it. Two screws held the top of the stove to the main cabinet. After removing these screws from the bottom of the stove top. Note all you have to do to find them is open the door and look under the stove top. The whole stove top swings up and back letting you access the burner elements. Three screws hold the element to the bottom of the stove top. Remove these and note the four electrical wires attached to the burner element. Make sure you mark or notate the location of each wire. Attach the new burner and hook up the wires to it. I put the stove top back down and plugged in the range. The new burner element worked but the switch didn't shut it off. I unplugged the stove and removed the the back plate at the top of the stove. The plate is held on by eight Phillips screws. You only need to take the top back plate off. Don't take the bottom one off. After removing the the plate I could access the switches for each heating element. The left front switch had scorch marks on it, so I knew that it was burned out. Another way is to test the switch with a continuity tester and see if there are any open contacts on the switch. I ordered the switch. It was delivered in two days. I removed the old switch by pulling the knob off the switch and removed one Phillips head screw holding the switch in place. I removed each wire and attached them just as they were attached to the old switch. I ratcheted the switch and plugged the stove in to the outlet and the new burner and switch worked great. I removed the old broiler by taking two Phillips screws out and carefully pulled the old broiler element out. I only pulled the broiler element about four inches from the back of the stove. There are two wires that slide off the broiler element. Remove them but don't let them get pushed back into the holes that they are located in or you will have to take the entire back of the stove off and push them back through there openings. I unfortunately did this and this added time to the repair job. There are two Phillips screws that hold the broiler element holding bar they are located inside the roof of the stove. Remove these screws and slide the old broiler element out. Slide this holder on the new broiler. The holder slides back and fourth on the broiler element so you can position it in the right spot. First attach the electrical connections by sliding on the two wires to the broiler. Push the broiler ends back into there holes and attach them with the two Phillips screws. Next slide the broiler holder on to the broiler element and then position the broiler on the roof of the oven. Attach with the Phillips screws. After doing this I plugged the stove in and turned on the broiler and it works great. There were alot of screws that held the back top plate to the stove and other screws that attached the switch, burner element and broiler element in place, so it would be a good idea to note were these screws are placed. Then there will not be a problem matching

Unplugged dryer from power source, used putty knife to release latches that hold top on, tilted the top out of the way, unplugged door lite, located the radiant switch, removed 1 screw,then undid 2 wires & lifted out switch. Reversed procedure plugged in dryer....wa la had dried a large load of clothes, took 1/3 the time to dry clothes at last. Thanks "PartSelect"

First, unplug power. The coils are easily accessible from the front of the dryer. Use a 5/16 nutdriver to remove two screws at the bottom of the bottom panel and lift the bottom edge of panel toward you. Pops right out. The assembly with the coils is on the front left. Use a small phillips to remove the coil-retaining bracket. Keep track of orientation of which coil goes where. Slide the suspect coil up off the column and slide the replacement in its place. Carefully slip off wire clips from old to new coil. Repeat for second coil. Reassemble and test.

Opened the dryer door - removed two screws on the left and two screws on the right - pulled the front panel forward and lifted it up to remove. The coils were located on the bottom right hand corner of the dryer, I vacuumed he area and then removed the two screws and bracket which hold the coil in place. Lifted the new coils off paying close attention to their orientation. Installed new coils. Align tab on top of coils with bracket. installed bracket and screws. Tested dryer and then replaced front cover. Very easy and rewarding.

Identified the rollers as the root cause of the drum not freely rotating. They also squeaked a little at the beginning of any cycle. I replaced the rear rollers and shafts using the parts from the roller replacement kit. Easy to do. The hardest parts was re-installing the belt.

looked up model on partselect and used the part by symptom section, chose the"will not start" symptom, based on that, the high limit kit seemed obvious, ordered part,received part in two days. watched repair video on this web site, followed the instructions, which were very clear, after unplugging the dryer, replaced both limit switches using nut driver, couldn't have been easier! I echo what other reviewers have said, you have customer for life! well thought out website providing excellent service to a person who wants to understand how things work and then fix it.