ADG20K3H Admiral Dryer - Instructions

I first unplugged the unit, unlatched the top cover, removed the wires for the door switch, then removed the two screws securing the front panel. I "propped open" the top lid with a 2 by 4. I then lifted away the front panel, removed the blower housing screws to expose the blower. Then I removed the snap ring on the blower shaft, the clamp holding the blower wheel in place, and slid the blower wheel off the motor shaft. Reassembly was in the reverse order. Was very easy.

I removed the front panel of the dryer by removing the 2 screw that secure it at the bottom and pulling upward to disconnect the cover at the top. I then removed the two screws that hold the metal cover that secures the 2 elements in place. I disconnected the wire plugs from the 2 elements, removed the 2 elements and replaced them with the new parts making sure to place them in the same positions as before. I then replaced the housing cover and tightened the screws. Then I replaced the front cover of the dryer.

After replacing all the other fuses and sensors I finally replaced the Radiant Flame Sensor and it is working perfectly.

After replacing the other parts and the heat still not coming on I read somewhere that the Radiant Flame Sensor is a normal closed circuit and when I checked with a meter it was open. I would have saved a lot of time and money if I had read that earlier.

Opened the top by popping the two fasteners holding it down. Did this with a screw driver. Took two screws out of the front holding collector in place and two screws out holding the front to the two other sides. Put front of dryer down on the floor. Removed old collector and used all other existing material from old collector to finish job. Wife could not believe how quick this was. Put back together was a snap too.

My husband and I used a screwdriver to pry open the top of the dryer, then unscrewed the two front corners of it from the inside. Next, we disconnected wires attached to front lid, then pulled the big barrel of the dryer away from the rest of it. We put a new drum roller wheel on the left side and greased the inside perimeter of it. Next, we took off the old cushion set, and stuck on the newer set, and greased drum glide as well. Lastly, we took off the "old" belt, and replaced it with the one we purchased from PartSelect. We forgot how the old one came off the pulley, but after much trial and error, we figured it out in a snap! (this is why this project took us longer than we expected)
In conclusion, this company for parts is wonderful and I have been referring them to all of my friends!

I removed the 2 screws that hold the ignighter & cover in place...unpluged the wire...replaced it with the new ignighter...thats when I found out that it was easier to take off than to put on...but I got it back into place...replaced the 2 screws...put the new belt on the drum...fitted it around the moter...pulled the wheel spring back to get it on tight...made sure the drum was fitted around the wheels...checked the tension...plugged in the wire for the ignighter...tested to see if the ignighter glowed...it did...I but the door back on the dryer...and it works...i thank my father for showing me how to work on machines...instead of letting me play with my dolls...thank you Parts select for getting my order to me in great condition & record time...

Opened dryer and removed drum. Replaced old blower wheel with new wheel, clamp and clipwhich was worn and was responsible for the noisy operation. Plugged in new ignition coils then replaced drum. Dryer works great now.

First off, the parts were exactly what I needed and arrived at my front door in less than 48 hours.
The repair was quite easy. 1. access the "guts" by popping the two clipps and open top panel like a car hood.2. remove the high temp doohickie with a nut driver, one screw, two wires.3. Remove the heating element from its mount. 4. remove the high temp fuse doohickie, By popping off its wires and little retaining bracket. 5. do steps (in this order) 5-1 replacing new parts. 6. spend three hours looking for the dryer brush, you know you have somewhere, to clean 5 years of accumulated lint out of the lint trap.7. drive to Ace, by dryer brush. 8. (most important step) clean the lint trap, or be forced to repeat steps 1-5. 9. Pop a cold one and relish the peace and quiet, devoid of spousal nagging to fix the damn dryer. 10. Take down clothesline in backyard.

Opened front panel .Tested both coils on gas valve.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.

I opened up the dryer as per the instructions I had received from PartSelect tech support. It was very easy to do. The only unexpected thing was that the original belt had snapped and in doing so the idler pulley was actually laying on the floor of the dryer's bottom. I had to figure out how it went, but that only took a minute and I popped it back into place. I held the drum by hand while pulling the dryer face away so it wouldn't fall and then I slipped the belt over the drum and quickly closed the front up again. I aligned the belt on the spot where the old one had been, pulled it through the idler pulley and over the motor and voila. Done. I closed up the dryer and was on to another "Honey Do" project within 20 minutes.

Very easy repair. Just needed to remove some screws to access the heating element area. The fuses are (1) just above the elements and (2) to the right side of them (if facing from the front). Alittle loosening with a philips screwdriver, removing blown fuses, replace with new fuses, tighten new fuses in place, replace outer screws and job done. Also made sure to fully clean lint collection area. I had a good amount stuck in there and it restricted air flow which caused the fuses to blow. It took 6 years worth of drying to make it happen.

Took out two front Panel screws and removed the panel. Removed Gas solenoid coil holding bracket by removing two phillips head screws. Disconnected the coil leads. and removed the coils. Connected the new coils to the leads and set in place. Replaced the holding bracket and the two screws. Replaced the front cover and the two front cover screws. Piece of Cake!

I lifted the top of the dryer cabinet, like the hood of a car using a screwdriver to pry it open. I removed the two screws in the upper right corner of the cabinet front. I disconnected the safty switch on the front door. The front of the cabinet can then be removed by lifting up the front off the pins in the base. With the drum exposed you can place the belt on and thread it through the two pulleys on the motor. Consult the diagrams provided on the PartsSelect website for the proper positioning of the belt on the pulleys. After the belt is installed spin the drum by hand one turn to make sure that it is seated properly on the drum and pulleys. Reassemble the dryer in the reverve order.

I removed the two screws holding the access panel, and removed the access panel. Then removed the lower air duct. I then checked the burner, The solenoid was not opeing the valve for the gas. I order the coils, in two day I had the coils and installed them. The dryer is working great.

After replaceing several parts including the thermostats the last part I replaced the coils were the defective part. I originally metered out the themostats and they appeared to be okay but since this was my first time I thought I might have been mistaken. It turns out the last part I thought it could be was the part that was defective. I will say that it is very simple to replace any of the parts involved. The hardest part was trying to open the dryer itself. But after having to do it 3 times, I'm now a pro. I also replaced the drum belt and since I had it open I also replaced the belf idler with a newer modified idler rolller.

Putting the belt back on is easy, but it helps to view the video or a picture to understand how the belt goes around it.