ADE9000AYW Admiral Dryer - Instructions

There are a total of six screws that have to be removed to do this job.
Take the lint tray out and remove the first two screws.
Secondly, remove the lower panel in the front of the dryer. You do this by inserting a screwdriver at the top portion and pry it off. Next, loosen the two screws under the top panel in the front of the dryer.
Now take your screwdriver and pry up the top lid of the dryer. The last two screws are in the inside of the front panel. They hold together the front and side panels. Remove them and be sure you have a support for under the dryer drum. (once you remove the front panel, the drum no longer has a way to stay suspended)
(Make sure you disconnect the wires attached to the front door, making note of which wire goes where.)
At this point, You can follow the easy instructions that come with your new belt.
If you have a little mechanical aptitude, this is a very easy project.

Turn the power off to the dryer. Pushed the two retaining clips that held the top of the dryer to the dryer sides. One on each side of the front. Table knife works really well to do this. Lift the top of the dryer up all the way. You will see the heating elements in the rear center of the dryer. There will be one screw holding the heating elements in place. Once you remove the wires from the heating element and remove the screw the heating element will lift out. Remove the heating elements and set down somewhere they will not get damaged. On the side the screw came out of there will be the heat fuse (as Maytag calls it). Remove the retainer by picking straight up on the retainer and the fuse will come out with the retainer. Remove the wires and replace the fuse and reinstall in reverse order.

Wife wanted a new dryer as it was useless without a knob and tired of using plyers to turn it. Went to internet, entered dryer knob, lead me to your site and item within two minutes. Ordered and received in 2 days. No tools necessary, just pushed it into place. Saved the cost of a new dryer.

This repair was so easy a sleeping Turtle could do it. You just remove the wiring from the old unit and remember which wire is on which terminal. Easily remove the old unit and replace it. Reattach the wires and you are done! Maytag is a very easy unit to work with. Just remember if you ever have to replace your Terminal Block, don't forget to order the brass nuts to attach the wires. Regular nuts will overheat and cause a fire hazard.

Opened top of dryer and found high limit thermostat burned in half. Thermostat is located on top of element. Replacement of thermostat took less than 10 minutes, using phillips head screwdriver.

If you were to do the Belt Replacement only, here is the quick synopsis:
1. Unplug dryer;
2a. Open lint door on top of dryer and remove the two phillips head screws that hold the lint bay to the metal dryer top;
2b. Next remove the two brakets holding the metal top to the dryer back (one screw on each bracket);
3. Use a flat-blade screw driver to pry off the top of the dryer (leaving the timer and start button area attached);
4. Lift off top and push back to expose just enough area so you can get to the two screws holding the dryer sides to the dryer front;
5. Unplug door switch;
6. Unscrew screws from #4;
7. With door open, lift dryer front (only about an inch) and then pry bottom of dryer front from dryer sides. The bottom of the dryer front is not screwed, just siting on Front Panel Clips;
8. Once the front is off the dryer, simply remove the belt and install the new one. Please note that while you are in here, you may want to inspect the rear drum seal and replace if it is worn to the point where metal is rubbing on metal. This is also a good time to clean out dust from inside this cavity to help extend the life of the bearings on the rollers and prevent dust from accumulating and gunking up the motor, etc.
9. Re-assemble tin the opposite order.
If you have any mechanical sense at all and you don't know anything about dryers, you will be surprised at the simplicity of the dryer.

Opened the top by popping the two fasteners holding it down. Did this with a screw driver. Took two screws out of the front holding collector in place and two screws out holding the front to the two other sides. Put front of dryer down on the floor. Removed old collector and used all other existing material from old collector to finish job. Wife could not believe how quick this was. Put back together was a snap too.

My husband and I used a screwdriver to pry open the top of the dryer, then unscrewed the two front corners of it from the inside. Next, we disconnected wires attached to front lid, then pulled the big barrel of the dryer away from the rest of it. We put a new drum roller wheel on the left side and greased the inside perimeter of it. Next, we took off the old cushion set, and stuck on the newer set, and greased drum glide as well. Lastly, we took off the "old" belt, and replaced it with the one we purchased from PartSelect. We forgot how the old one came off the pulley, but after much trial and error, we figured it out in a snap! (this is why this project took us longer than we expected)
In conclusion, this company for parts is wonderful and I have been referring them to all of my friends!

Ordered my part from partselect. Com (even easier than installation) unpluged the dryer,removed all knobs from face plate ,removed three phillips head screws across top ,removed two 5/16 head screws from timer( behind cycle knob) tilted back face plate unpluged one wire at atime from old timer placed back on new timer then reverced the process. Problem solved

First I unplugged the dryer and slid it a few inches out from the wall. I slid 2 putty knives in the front top about 3 inches in from the sides. Released the top and raised it up. I used a multimeter to test the hi limit and the element, both were operational. I used a screwdriver to remove the 2 screws that hold the front panel in place. I lowered the panel slightly and disconnected the wires mentally noting the proper placement. With the front panel on the floor, the problem was obvious. I cleaned the lint clog under the lint screen that had caused the issue to begin with.I used a shop vac and cleaned the vent area as well as the front panel. I used a nut driver to remove the 2 screws that held the thermostat in place. The old thermostat fell apart in my hands. I covered the bare exposed wires with electrical tape. ( must have gotten HOT) and reattached the connections to the new thermostat, then replaced the 2 screws that held it secure. I stood the front panel back up and reattached the electrical connections and the 2 screws. I lowered the top and plugged it back into the outlet. I turned it on. It works like new.

0. Opened packaged and receipt verified the parts against the drawing and packing slip.
1. Disconnected dryer from power source by pulling the plug.
2. Removed the two screws (philips) on left and right side of the main frame to allow access to the blower assembly.
3. (Optional)Verified power dead at the circuitry near the blower wheel assembly (former navy electrician- "check it dead").
4. Removed the two screws at the base of the wheel cover using the screw driver (philips). The other screws on the assembly cover required the use of a 1/4" nut driver.
5. Opened the assembly, and with a flathead, pried the Retaining Omega ring, and removed the damaged wheel (broken vanes and missing straight end of the center ring) and disposed.
6. Inserted the new wheel on the shaft and was able to manually do it until about 3/4 of the way; to get it fully insert it, tap it with a mallet (tap the center of the wheel and avoid the blades).
7. Insert the retaining ring and operationally test it by manually rotating the tumbler and verifying the blower wheel moves freely and without noises.
8. (Optional) Vacuumed the lint and dust from the wheel assembly, the filter and exhaust line (found several broken pieces of vanes there). Inspected heater assembly for obvious signs of damage
9. Re-installed the assembly cover and the main cover back to the frame
10. Reconnected the plug to outlet and tested by a starting a 10 minutes cycle- no noise and constant flow of air.
11. Smoked a Motecristo Churchill as I grilled the steaks and pondered the greatness of the free market.

,

I just inserted the door catch, which by the way fit in perfectly. Thanks. Took 5 seconds to repair.

I opened up the dryer as per the instructions I had received from PartSelect tech support. It was very easy to do. The only unexpected thing was that the original belt had snapped and in doing so the idler pulley was actually laying on the floor of the dryer's bottom. I had to figure out how it went, but that only took a minute and I popped it back into place. I held the drum by hand while pulling the dryer face away so it wouldn't fall and then I slipped the belt over the drum and quickly closed the front up again. I aligned the belt on the spot where the old one had been, pulled it through the idler pulley and over the motor and voila. Done. I closed up the dryer and was on to another "Honey Do" project within 20 minutes.

I lifted the top of the dryer cabinet, like the hood of a car using a screwdriver to pry it open. I removed the two screws in the upper right corner of the cabinet front. I disconnected the safty switch on the front door. The front of the cabinet can then be removed by lifting up the front off the pins in the base. With the drum exposed you can place the belt on and thread it through the two pulleys on the motor. Consult the diagrams provided on the PartsSelect website for the proper positioning of the belt on the pulleys. After the belt is installed spin the drum by hand one turn to make sure that it is seated properly on the drum and pulleys. Reassemble the dryer in the reverve order.

Unscrewed the two fasteners, rerouted one wire using a wire coat hanger, plugged in the new moisture sensor to the two wires and fastened the the sensor in place using the two existing screws.