Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ADE7000AYW > Instructions

ADE7000AYW Admiral Dryer - Instructions

All installation instructions for ADE7000AYW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ADE7000AYW
631-645 of 725
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broken dryer belt

  • Customer: joe from partlow, VA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Thousand dollars for a new dryer or twenty bucks for a new belt. Thank-you parts select. Ordering was easy and the instructions were bang on!

Dryer would not continue to provide heat to dry laundry.

  • Customer: Nick from Surprize, AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Both washer and dryer always worked perfectly. Suddenly, dryer wasn’t drying laundry properly. Problem... no heat. Cheapest price I could find calling for appliance service was about $160 to replace coil set but no one would tell me this would fix the problem. This was after calling a number of repair firms and trying to get a somewhat close estimate of what my problem was and what the repair cost. Not knowing, I might have just paid the $160 but what turned me off was having a service call fee of anywhere from $50-$80 with no one willing to tell me what the problem might most likely be before coming out or give me an estimate over the phone other than a range of $160 - $275. I just did not want to have someone come out for $50 -$80 and tell me that I needed to spend $275 and still owe them the service call even if I did not agree.
Found diagnostic and repair instructions help on line. The diagnostic information indicated a high probability, roughly 50%, that replacing the coil set would solve the problem and found the coil set cost $19.21 plus shipping, so I ordered the coil kit for total of $26.70. Note... I am a 71 year old amateur never having worked as a repairman of any kind except for my own needs.
The repair itself took less than 30 minutes start to finish and was one of the most straight forward, glitch free, easy repairs I have ever done. This is a gas dryer but still uses 110 power so I unplugged the 110 power cord from outlet. Followed suggested guidance on opening the dryer cabinet from the front and presto, the coil set I needed to replace was immediately right in front with easy access. Removed 2 screws for the hold-down bracket, slipped off both coils, one at a time, removing the wiring connection for each coil and then reconnecting to each new coil before slipping each new coil back into place and reattaching the hold down bracket. Reinstalled the dryer door and cabinet front in reverse order from taking off... 4 screws total. Plugged in the 110 power cord and put in a damp load of freshly washed laundry. Presto... 30 minutes later... dry laundry. Note... could do the same repair again in half the time since I took it slow and careful 1st time and also took time to remove dust before completing repair. I like things to look like new inside and out and it did when I was done. $26.70 and good as new. Why I didn't spend $160 - $275 is pretty obvious now.

Was not drying well

  • Customer: Carol from Ada, MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
I first replaced the temperature sensor. That did not help and when doing investigation when thr drier was warm I found the vallve would open and close if I touched the coils

broken belt

  • Customer: HUNG from KENT, WA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
follow video and fix.

The dryer was making a terrible sound and it stopped turning.

  • Customer: Cindy from Pelzer,, SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
I lifted the top of the dryer. I unhooked the hangers from the door and took it off. I pulled the drum out, took the broken belt off, slid the new one around the outside middle of the drum, turning the rib side of the belt out,and ran the belt through the pulley attached to the bottom base of the dryer (tension pulley, right hand side), slid the drum back inside the dryer frame, reattached the door, closed and snapped the dryer lid and it worked great!!

Ancient Kenmore Dryer

  • Customer: Franklin from Eureka, CA
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Your customer service was great, but your video wasn't particularly helpful because of the extreme age of my dryer. For one thing, with these really old dryers, you don't have to slide the drum out at all; you just unscrew the front panel and slip the belt in that way. The printed diagram that came with the belt helped me figure how the belt slips through the pulley assembly, but the drawing could have been more clear. In spite of my bickering, I probably saved $50 fixing it myself.

Drum not turning.....broken drive belt

  • Customer: Ashby's from Foster, WV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Disconnect electric power, the top & cabinet are connected by 2 reusable locks about 4 inches from each front corner, use a thin flat putty knife or similar object, push inward on a lock while lifting gently on the front of the top piece, then let the top rest against the wall. ( a wire on each end of a safety switch for the dryer door may need disconnected) Remove a screw from each front corner of the cabinet, then pull upward on the loose front panel to access the drive motor, remove old belt. install new belt by lifting the front of the drum just high enough to allow the new belt, place groves of belt against the drum and around the motor pulley and belt tensioner, re-install cabinet front, (re-connect safety switch wires) return top and push down at cabinet locks.

Flame would go out after start up. The Igniter would glow not light

  • Customer: Jay from South Bound Brook, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Repair itself was not hard, Pop top, unscrew front panel and pull forward to get at the coils under the drum. --THIS IS THE KEY POINT i ENCOUNTERED: I tested the coils and the resistance was right according to the schematic. But still the flame would go out after while. --on a whim I pulled the front cover and tested the coils immediately after the flam wouldn't re-light.---When the coil got warm, it would open (no continuity). When it cooled down again the correct continuity would return. Replaced the coil and no more problem

broken belt

  • Customer: Joy from livingston, LA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
It was really easy I watched your video on how to do it the video went step by step and was very helpful

Dryer stopped drying cloths out of the blue. Everything work fine but no heat.

  • Customer: scott from bend, OR
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I watched a part select youtube video on possible fixes for the problem I was having. Ten minutes and two videos later I had the part out and identified as the problem. I ordered the part ($42.00) which arrived four days later. Spent ten minutes replacing it in machine, turned dryer on and went right back to performing the way it has for the last 12 years. Easiest thing I did all day. Saved me $400 bucks too. Thank you.

Broken Belt

  • Customer: Jeffrey from Bensalem, PA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watch the video you sent me, and every thing fell into place

looked at heating element saw wire was broke

  • Customer: Steve from Northfield, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Took less than five minutes to fix a couple screws and take some wires off and pull it right out. Called local apliance store if they had part wanted more than partselect with next day shipping

Replace Drive Belt

  • Customer: William from Marlborough, CT
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
What a pain in the butt to route the belt thru the tensioner! There's room for only one hand in there. The guys who do this for a living must have some secret. My solution was to drill a 3/16 hole thru the side, make a j-hook from 8-32 threaded rod, use that and a wing nut to pre-load the tensioner, route the belt, then slowly back off the wing nut until the belt was tight. It works. . . .

Broken lint filter

  • Customer: Katherine from Indianapolis, IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Wrench set
  • 0 of 0 people found this instruction helpful
Replacing the lint filter was, of course, the easy part. The rest of the time was spent removing the front of the dryer and cleaning out all the lint that had escaped through the old broken filter. I completely took apart the lint traps inside the front, vacuumed everything out, and replaced the ductwork to the outside that was almost completely blocked with lint. Please take the time to inspect your dryer, and do this if necessary! I feel we prevented a house fire by getting to this in time - and I will be more vigilant in the future.

Dryer quit heating.

  • Customer: John from La Crescenta, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed two screws from front panel and lifted front panel away, Turned it to the left so I could keep the door switch connected. The dryer would heat when it was first started, but then the burner would go off and would not come back on. I ran the dryer with the front panel off and could see the igniter glow and light the burner, but after the burner cycled off, the igniter would come back on but the gas would not come back on. I could tell it wasn't the thermostat because the igniter would come on, so I knew it must be the gas valve, and therefore probably the coils. The instructions on the website said that the coils were frequently intermittent, so that seemed like the problem. I tried checking out the coil resistance with an ohmmeter to try to confirm that, but couldn't really tell anything that way. I ordered the replacement coils Tuesday night, selecting the cheapest shipping; they shipped on Wednesday, and were delivered on Thursday! Amazingly fast! Removed two screws from the clip that holds the coils in place, unplugged the old coils, swapped in the new coils, screwed the retaining clip back on. All done. Before I replaced the front panel, I watched to see that it operated correctly. I could see the burner cycle off, then after a bit, the igniter glowed, and then the gas came back on and lit, just like it should. Problem solved. Put the front panel back on, and that's all there was to it. Well, I did vacuum out some of the dust inside the cabinet while I had the cover off. Just out of curiosity, I checked the resistance of the new coils before I installed them to compare with the old ones. Couldn't see much difference.
All Instructions for the ADE7000AYW
631-645 of 725