ADE7000AYW Admiral Dryer - Instructions

carefully pulled out old seal, then popped in new seal

My husband who is in a wheelchair and his freind who had never worked on a dryer,watched the video online and boom! just like that it was fixed!Some nut told me it would cost too much to fix,To just get a new one!Boy am I grateful for you!Thank You.virginia.

First and foremost, PartSelect is awesome! I placed the order on a Monday afternoon with regular shipping, and I had the belt Tuesday evening. Total repair involved removing several screws to open the top and front of the dryer, then installing the new belt. Pay close attention to the the dryer seal - make sure this is completely set. This was a very, very easy repair, and it cost me less than $20 for part and shipping! Also, the video on the PartSelect site shows exactly how to make this repair, and was very helpful.

The repair could not have went better. Did just as video showed and it was up and running in 10 min..The video was very helpfull.

The hardest part is figuring out how to get the unit open. You have to take out the brackets that appear to hold on the timer section and you have to remove the screws under the lint filter. Once you have the top off then you remove the screws that hold the front panel on from the inside. I decided not to remove the drum it seemed like a lot of hassle, instead I went down and got a right angle screwdriver, the terminal valves are in the front of the unit and you only have to remove 2 screws to remove the retainer which holds them both in place. The drum is in the way so you can't use a regular screwdriver and the right angle is a bit slow going but I think it is actually faster than removing and replacing the drum for a novice like myself. Replacing the coils took about 2 minutes and then reassembly another half hour. But the Dryer works great again and for $70 it was well worth it.

DISCONNECT dryer from power source. Removed 2 screws holding lint filter housing, pulled top cover forward to release the two plastic keepers, raised the top cover. Disconnected two wires from the door switch, removed two screws holding front pannel assembly, slightly raised off of two hooks and removed. Supported drum by placing a strap from one side top under drum to the other side top. Removed broken belt. Vacuume any lint from under and around drum. Slid new belt over drum, under drum stuck folded end of belt through tensioner and on to motor pulley. Reinstalled front pannel assembly by lowering onto two hooks near bottom, removed support strap, reinstalled the two screws, hooked up wirind to door switch, lowerew top back in place inserted two screws back into lint filter housing. Plugged up to power supply. Test operate.

I bought from you and received part in timely manner. I got it out of the box and replaced. It's better than the one I got new with dryer. Thanks, P.Blades.

Lifted top off dryer using a putty knife to release it. Took off front door using a nutdriver, disconnected door switch. Put door to side and reconnected switch. Dryer would turn on but the igniter would not come on. Disconnected gas valve assembly from gas line. One bolt holds the igniter assembly and gas valve. Took out whole assembly and replaced the igniter. Old igniter had a hairline crack. Put it all back together and Works like a charm. Also cleaned out tons of lint from interior.

unhinged top panel. removed front panel. installed belt and reinstalled front and top panel.

I removed the old door seal and installed the new one algining the slots with the inserts and the seals. Old filter out, new filter in. Install was successful but dryer still not drying even though it's producing heat. I guess I will need a replacement.

Replaced the flame sensor since it was believed to be the problem contributing to the lack of flame in this gas dryer. However, this part did not correct the problem.

Unplugged dryer from electrical outlet, lifted up top of dryer, removed overheating sensor and dryer element with 1/4"socket being very careful not to drop screws into dryer, replaced dryer element and heat sensor, closed top lid of dryer, plugged back into outlet and tested for proper operation.

open machine up and replaced the new belt.

removed frt cover & drum, replaced solenoids, cleaned the unit interior

just took off the front panel took off the belt and replaced it with the new one we watched the video pretty easy