When the igniter reaches a high enough temperature, these coils (Coil Valve, Dryer Gas Valve Coil Kit, Dryer Valve Coil Kit, Gas Valve Solenoid) work together to open the gas valve and allow the gas t...
This genuine OEM washer has a 3/4 inch outside diameter. This thrust washer can be used on most makes and models of dryers. A complete list of compatible dryers is available below. The washer is found...
The metal retaining ring, which is under an inch long, holds the rear wheels on the axels of the dryer. The main reason why it would need to replaced is if the retaining ring has sprung out of place o...
This cylinder felt seal is used in dryers and is located between the back of the drum and the rear dryer panel. If your dryer is experiencing any of these symptoms, replacing the felt seal could solve...
This part replaces two terminal switches in a dryer and prevents the dryer from running when the door is open. This includes two connectors. If your dryer will not shut off, start, or does not tumble,...
This spring retaining clip is just under 1 inch long. The clip is made entirely of metal and is attached to the back wall of the washer, under the console. If your washer is vibrating and louder than ...
This kit contains two glide brackets and four screws.
$74.64
In Stock
Questions And Answers for ADE3LRGS171TW01
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
3 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
George
December 27, 2022
What is the part number for the correct heating element for this dryer?
For model number ADE3LRGS171TW01
Hi George, thank you for your question! The compatible heating element for your model is part number PS11757549. Please reach out to customer service if you need help placing an order. Glad to be of help!
Shuts down after approx.30 min. Timer and controls ok. Heat element cycles ok.Restarts and runs ok after 20 min. idle.Duct work clean and open.
For model number ADE3LRGS171TW01
Hello William, thank you for asking. We would recommend checking the high limit thermostat, part number PS11748479, to fix the issue. We hope this helps!
heats, but heat output is dimished, and have to run thru 2 or 3 drying cycles to get clothes dry
For model number ADE3LRGS171TW01
Hi Kent, thank you for your inquiry. Make sure your dryer's lint filter is not clogged, which can restrict airflow and cause clothes to take longer to dry. Check your dryer's vent is not clogged with lint or debris, which can also restrict airflow and cause clothes to take longer to dry. Also, make sure your dryer's drum is not too full, which can cause clothes to take longer to dry. It is best to dry clothes in smaller loads. If this does not help, we would recommend checking the gas valve solenoid, part number PS334310. We hope this information helps!
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are
... Read more located on top of the gas valve. I borrowed my neighbor"s ohm meter and touched the two probes on the coils terminals to check for continuity and found that one of the coils read zero. I then took both of the coils out by removing two screws and tested each coil again. One coil read 500-850 and the other read zero. This meant that it was no good so I called for the part and received it in three days. I reassembled the parts and turned the dryer on and it fired up after a few seconds. It works as good as new. The part plus shipping was less than $30. My repairman would have charged me $150-$200. While the dryer was apart I gave it a good cleaning with a vacuum and a toothbrush in delicate areas. I also removed and cleaned the lint trap housing by removing two nuts. I didn't know much about gas dryers, but thanks to PartSelect I easily fixed it myself.
There was no problem with lint build-up within the dryer & the exhaust vent. I removed the gas cycling thermostat & thermal fuse from system & dryer still was not operating correctly. The radiant sensor & hi-limit thermostat both seemed to be operating correctly. That left either of the two coils as the culprits. I replaced both coils
... Read more& the problem was corrected.
Timer wasn't working on the regular cycle so I replace it with a new one from partselect. It still wasn't working so I ordered and replace the cycling thermostat, the thermal fuse I also cleaned the vent and dryer it still didn't work so I read the diagram for the electrical and found that a coil for the gas valve is line with timer. I or
... Read moredered the coils for the valves, replaced both valves and tested the dryer and it work just like when I first bought the appliance.
