Models > ADE25K3A

ADE25K3A Admiral Dryer - Overview

Get Parts and Repair Help for ADE25K3A

If you know the dryer repair part you need, you can browse the list of all parts on the ADE25K3A, or you can search by name or part description. You can also find your part by where it is located on the ADE25K3A by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for ADE25K3A parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$13.44

Multi Rib Belt - 92-1/4"

This dryer drum belt has four ridges, three grooves and is 1/4" wide.

$37.91

Rear Drum Support Roller Kit

Included in this rear drum support roller kit are 4 screws, 1 spacers, 2 washers, 2 retaining rings, 2 rear rollers, and 2 cylinder support shafts. *** Note: Per manufacturer this kit has been updated now to have one spacer that is the thickness of 2 spacers. To get these parts separately, please search by model#.

$2.70

Blower Wheel Clamp

$2.70

SCREW

This screw is sold individually.

$2.70

Screw

This screw is sold individually.

$21.53

Thermal Fuse

$8.76

Drum Glide and Cushion Kit

Pad has adhesive backing.

$4.46

Retaining Ring

This part works in conjunction with the blower wheel.

$30.16

Front Drum Support Roller Replacement Kit

This front drum support roller kit is used for many gas and electric clothes dryers. Included in this kit are one right side glide, one left side glide, two adhesive felt pads, a m...

$4.46

Timer Resistor Assembly

This timer resistor assembly is made of ceramic and metal.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broken tumbler belt

  • Customer: Michael from San Antonio TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 79 of 80 people found this instruction helpful
1. Removed the screws from the lint catcher
2. Removed the bolts from upper rear of dryer
3. Pried off the dryer top from the front (it rests on rear hinges)
4. Disconnected dryer door wiring
5. Removed bolt from inside upper front corners; removed front panel (be careful: the edges are sharp and the tumbler will fall when it loses suppor... read more

Broken belt - drum would not turn

  • Customer: Gary from Oakland MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 43 of 47 people found this instruction helpful
Started out taking the back off, then found online that access is from the front and much easier to get to. Simply pop the hinges in the back of the top panel and then the front of the top is popped off. From there, it is easy to remove the old belt, clean the innards (found 31 cents) and replace the new belt. It was a little disconcerting to see the idle... read more

Dryer would not run

  • Customer: Ron from Rutherfordton NC
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 38 of 41 people found this instruction helpful
Unplugged unit, lifted the top cover, removed heater element screw, lifted out element, lifted out thermal fuse bracket. Removed wires from thermal fuse, confirmed was open curcuit at room temperature. Attached wires to thermal fuse, inserted fuse into bracket, slid bracket onto clip on side of box that housed the heater element, reinstalled heater elememt... read more