ADB2500AWQ Amana Dishwasher - Instructions

removed coverpanel with star shaped tip on cordless drill. hardest part was removing the wires from old handle. i had to use 2 pair of pliers to get them disconnected. plugged wires into new doorlatch. set latch in place and reattached coverplate. works like new.

Couldn't justify having a repairman come to the house for a 5 year old appliance, so there was nothing to lose by trying to do this myself.
I removed about a dozen screws that held the inside door panel to the door, two of the screws held the handle assembly in place. Pulled the wires off of the old handle assembly with a pair of pliers, fastened the wire harnesses to the new assembley and reinstalled the door panel. Repair was simple.

the part we received has changed, and so it did not fit our dishwasher after all. i was able to remove one flapper from the part and put it on my old one, and now the water pressure is much better, and the dishes are actually getting cleaned.

All I did was put the new wheels on. They were really fast with shipping. I put my order in one day and the parts were there the next.

Removed screws holding inside liner to door. Seperated the two revealing latch assembly. Removed two electrical plugs from latch. Installed plugs on new latch assembly. Put door and liner together and reinstalled screws with screw setting of driver on lowest torque setting. Hand tightened and tested. Whole job less than 10 minutes. Super easy, wife impressed!

Removed all the screws holding the shroud, filter, wash arm, etc. Installed new shaft and chopper blade, then reinstalled impella on new shaft as described on the easy to follow instructions.

just had to remove the stoppers and slide the track on and then replace the new stoppers.
most of all i was pleasantly surprised at how fast the parts arrived. i ordered them thursday morning and i was installing them friday morning .

piece of cake. you need the special screw driver bit to take the back panel off the door, Then take the wires off and put the new assemble in . button up and you are done.

Removed inner door panel. Removed latch . Removing wire connectors from switches was difficult. Replaced latch. Reassembled. Done.

Calcium build up from our hard water had plugged varous parts of the dishwasher. Dismantling all the parts for cleaning had resulted in my braking the retaining tabs on the upper sprayer arm, that snaps into a plastic clip that attaches to a flat water distribution tube running from the base of the dishwasher up the back and then over the inside top of the compartment. Replacement is literally a snap. Make sure your get good visualizaton of how to remove the various plastic pieces from the metal or plastic clips that secure them to the inner wall of the dishwasher. Don't do the work only by feel; as I tried to do. Positioning your body to get a good look is, at best, awkward

Open the door completely. Inside of the dishwasher door, remove all of the screws that hold the panel. Remove the broken Latch assembly by unplugging the two electrical wiring connections. Connect the new replacement Latch assembly to the electrical connections. Position it as it should be. Realign the panel cover and replace all the screws! [**Be careful to not "strip" the the receivers that the screws go into. I would suggest to hand tighten with a screwdriver. ]

Upon noticing that my latch was broken I removed the 10-12 torx scres from the inside of the front panel. After lifting up the inside panel, I removed the two floats from the latch assembly. I did not turn off the power at the breaker but did get a few volts in removing the float switches. When I received my parts, it took about 15 minutes to reattach the handle kit to the front panel and seal up the door. I did turn the power off at the breaker so there was no issue in stalling the wires and float switches to the handle assembly. I di order both the Latch and Latch Assembly that was shown in the picture without the latch. I was happy to see the latch already atteched to the latch assembly and I have sent the latch back for a full refund. Easy assembly and install.

turned of braker and thin removed the screws that held the frunt pannle on and unpluged the door handle switches and pluged in to new one thin placed ever thing were it belonged and put screws back in

Removed door facing screws, unpluged switch wires, attached wire plugs to new switches on handle and replaced screws. Finished.

printed instructions from your site. said would take 15 minutes. took about 5. take out the screws maybe 16 swap out handle and replace screws. whole job could be done during one set of comercials for law and order.