ADB2500AWB Amana Dishwasher - Instructions

The real cause of the leak had nothing to do with the foam strip. The latch for the front loading door at the top needed to be adjusted to hold the door in tighter to the rubber door seal. This simple adjustment stopped the leak but since the foam seal was all encrusted with dried detergent from probably years of absorbing the leak, I replaced it with your new foam strip. I used a screw driver with torx bit and removed the stainless screws holding the inner door to the outer door. Once these were separated I removed the old foam strip using a putty knife and lacquer thinner. Placing the new strip onto these cleaned surfaces was the easiest part of the whole repair.

The first thing I did was read the all of repair stories that others had submitted. Then I set the timer and chucked up the Torx bit in my electric drill/screwdriver. There are 10 Torx screws on the inside of the dishwasher door and they came out very quickly. The top two screws hold the latch in place. I lifted the inside stainless steel cover to get acces to the latch. There was enough slack in the wire that I was able to remove the latch from where it was and extend it above the door. This let me lay the stainless steel liner back onto the inside of the door without removing or disconnecting the soap dispenser. Thus exposed, disconnecting the connectors from the old latch and reconnecting them to the microswitches on the new latch was a breeze. Once connected, I reinstalled the latch assembly, repositioned the liner correctly and replaced the ten screws. The entire job, including putting my tools away and cleaning up took eight minutes. I did it on my lunch break. The eight minutes included pulling the circuit breaker and reconnecting it (very important, that step). The new latch/handle assembly completely fixed the problem.

Removed screws around perimeter of interior door panel. Latch was loose at this point so all I had to do is disconnect 2 wires and reattach those 2 wires to new part, position new latch in the proper place and fasten interior panel into origianl position. That was it!!!!

Turned off water and power to the unit. Removed kick plate from under the dishwasher to access the water contol valve. Placed an absorbant rag under the water valve and water line. Disconnected solenoid on water control valve from electrical connection with my fingers. Used a standard adjustable wrench to disconnect the water line from the water control valve. Then used a 1/4" nut driver to loosen the two bolts that hold the water control valve on to the mounting bracket. Pulled the water control valve slightly forward to disconnect the water feed line to the dishwasher. Used a blunt end plier to pinch the clamp open and slowly wiggle the feed line off of the water control valve. Then removed 90 degree elbow off of the water control valve and used pipe dope and connected the elbow onto the new water control valve. Replaced water control valve in reverse order and utilized new hose clamp to reconnect feed line to new water control valve. Saved door seal for future use, when seal goes bad.

First I had to go out and buy a Torx driver set, then I removed all of the Torx screws around the inside of the door panel. After that the door latch was free and I saw my problem, a broken retainer on the door latch assembly. I ordered a new door latch assembly and when it came in I removed the two electrical leads, set the new door latch assembly in place, attached the two electrical leads and reassembled the door panel with Torx screws all around. The new latch worked just like it was supposed to.

It was my first time repairing a dishwasher. I was a little worried. I also wasn't sure about how to remove the drain pump. Well, the hardest part was just getting the dishwasher out from under the counter. I did find a crimp in the drain line that probably contributed to the original pump going out. I fixed that, removed the old pump by removing one screw holding a stablizer bracket and twisting the pump connection. The original bracket is needed, so I removed it from the old pump, attached it to the new pump and reversed the removal process and secured the pump by reattaching the stabilizer bar with the single screw. I then slide the dishwasher back under the counter. Runs great. Easy repair. The part was shipped and delivered on time. Very impressed with the process and will order my appliance parts from you in the future.

Had to insert putty knife in the top of latch opening and press up to release the latch so the door would open.

Turn off electric to unit.
Removed the 12 star screws on the panel inside of door.
Pulled out the two wire plugs from the door latch unit, had to use a screwdriver to help push out the metal pronges.
Insert the plugs in the new unit and align the latch pivot point on the door and the two holes with the holes for the inside panel.
Replace the screws.
When the door is closed the latch will be pushed into place and the door is held closed.

I could not reach the heater element nuts from under the dishwasher so had to pull out the dishwasher. I removed the screws around the front of the dishwasher and pulled it about half way out before the water inlet pipe and the electrical wires stopped me. I shut off the water, unhooked the copper pipe, and unhooked the electrical wires (shut off circuit breaker first). Pulled the dishwaser out so I could remove the element nuts and wires to the element. Removed the old element and installed the new one - the old nuts would not fit. I went to a local appliance parts store and found that my element is no longer made. I had the correct replacement element but you need to order the nuts also. Luckily, the local store had a small brass nut that worked. Reattached the electrical wires to the element, pushed the dishwasher half way in, reattached the water inlet and electrical wires, pushed the dishwasher all the way in and scewed back into the cabinets. All is well now and the dishwasher is working much better.

First I read all the reports for not cleaning properly already listed on this site. I had to replace the docking station with flappers. When I removed the station I lost the flappers down the water delivery tube just like Jon said I would in his repair post so I removed the water distribution assembly fished out the old flappers and snapped in the new.
But then I figured I might as well check out the accumulator while I was in the tub anyway - I had read that you need Torx screwdriver bit, which I had, undid the screws, pulled out the accumulator screen which was about 80% clogged, discovered I need a new chopper blade and my impeller is disintegrating, put it back together and lost ten minutes looking for the three screws I had incorrectly put in too soon, and now it is cleaning a packed full load like it was supposed to do.
**I love this site - I went to the virtual repairman and it listed every problem I had with this appliance in the order they happened (door latch broke years ago). - I think I am going to look up stuff that I own so I will know ahead what could go wrong with them.

And absolutely NO DUCT TAPE was used in this repair.

The spring mechanism is on the side, so you have to pull the dishwasher out onto the floor. To do that, you have to remove the floor molding (preferably without breaking it) and remove the base coverings (painted metal plates on the bottom of the washer. Unscrew the side gasket plates on the side of the dishwasher (just inside of the door) where it attaches to the cabinet and the screws in the braces at the top (inside the door) where it attaches to the counter top. Now you will be able to slide the washer forward to look at the sides where the door springs are. Depending on the floor, you may have to raise the washer's front feet. They screw up. As you pull the washer forward be careful to not mess up the insulation which drapes over the top and sides. You only need to come out 1/3 of the way to see the sides where there is a plastic wheel at the forward bottom corner. As you move the door up and down you can see the hook where the cable goes and further up the side you can see several notches where the spring goes. Hook the cable and bring it around the wheel and attach it to the spring. To reinstall, just follow these directions backwards. Good luck.

I wanted to get the dishwasher cleaning better and thought that maybe the accumulator needed to be replaced. I figured that I'd swap out all the spray arms as well, just for good measure.

I needed Torx screwdrivers (T15 and T20, I think - not 100% sure on that) and patience because there's really quite a lot of screws to get the accumulator out. Finally got to it and it didn't look damaged, but replaced it anyway.

The spray arms are easy - they just snap in except for the lowest one, that had a plastic nut. I ordered a replacement nut just in case I broke this one (you know how that goes) taking it off. Well, it took pliers, but it came off ok.

In the end, my dishwasher is happy and cleans much better now.

After finding out that the impeller shaft was stripped (plastic) I quickly found the correct replacement on partselect.com by using my model number.
You do not have to remove the dishwasher, if you know what is wrong. But, throw the breaker switch and turn off the water! After removing the spin washer arm, Undo all of the torx screws and pull out the plastic filter looking plates along with the center plastic water jet. This jet provides water for the upper washer assembly. You may have to pop that upper assembly out to protect it from damage.
The black impeller should just pull out if the plastic shaft is stripped. Otherwise, unscrew the small torx head and remove the impeller. You can remove the blade at this time and unscrew the plastic shaft by unthreading it while keeping the motor from spinning. (I shoved a screw driver underneath the dishwasher through the motor. Also the motor is just floating on the rubber gasket and can easily pulled out to accomplish this task. It's heavy and has a plug attached to it. You'll see where you can shove the screw driver. This comes in handy while installing the new shaft, because it is metal. Which is a great, long awaited upgrade for the Maytag Quiet Series. Once you find which shaft to use, (which correct inner thread, course or fine), install it with the great directions that come with the part. Putting all the stuff together is not as bad as one would think, there is only one way for it to go back together. After installation is complete, turn water and breaker switch back on. Run a cycle and listen for the washing cycle against the wall of the washer. If you cannot tell the difference, you can unscrew the white lock arm and insert it into the door. Turn it on and watch how a dishwasher works. Get ready to get a little wet. Towels!

The original brackets that hold the water distribution manifold to the back and top of the tub came off the "X-shaped" plastic posts on the tub walls. That caused the upper wash arm to sag down into the travel of the upper dish rack and was broken off when the rack was pushed in.
I bought 2 new brackets and a new wash arm. The new brackets had a smaller aperature than the originals and fit tightly onto the plastic posts, holding the manifold firmly in its proper location. Replacement of the brackets and the new wash arm took less than ten minutes and required no tools!

disconnected unit (electrical, water, and waste) un mounted from countertop, removed from under countertop, unscrewed hose clamb, cut off wire tie. Attached new hose and wire tie (not included) reversed above steps. Done in about 15 minutes

Not being very computer literate, the most difficult part of the entire venture was navigating your web site. But I finally found the part I needed. I paid on line with a credit card, and received the part within a few days. I popped it in the dishwasher, and it took three days before my son noticed it.
He was surprised and I was proud to say " I ordered it on line."
All's well that end's well.
I would difinately use your service again.