Models > ADB2200AWW > Instructions

ADB2200AWW Amana Dishwasher - Instructions

All installation instructions for ADB2200AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ADB2200AWW
76-90 of 478
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The dishes in the dishwasher weren't getting clean. I decided it would be cheaper to replace the clogged wash arm myself, before calling a repairman.

  • Customer: Georganne from Carolina Beach NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 6 people found this instruction helpful
First, I removed the screw, then I took off the old wash arm, then I replaced the wash arm, and replaced the screw. Nothing could be easier!

broken door handle

  • Customer: Martha from Akron OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
In less than 5 minutes we took the screws out, fixed the latch and had it back together again. The amazing part of the story is the perfect diagrams and helpful instructions from Part Select. I ordered the part one day and by noon the next day the dishwasher was fixed!

Dishwasher wasn't heating the water and dishes were not getting clean.

  • Customer: Victoria from Greenleaf WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
This isn't a how to fix it....it's what part was bad. I had originally contacted the local Maytag repair center and the owner swore up and down that our problem had to be the thermostat and not the heater. He said he had only replaced maybe 5 heaters in 15 years. But our heater looked like heck, with hard water deposits and all, and it wasn't that old, but we went ahead and ordered the thermostat from PartSelect, which came in a day. The problem wasn't the thermostat, so we ordered the heater from PartSelect (again, only one day delivery) and our dishwasher is working again. The heater coil actually had a hole in it from some sort of corrosion. My 18-year-old son did the repair job in a jiffy.

Door handle stopped engaging

  • Customer: Harold L. from winamac IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
First I watched the repair video provided at your site. Once I got the right part, it went like a breeze. Just a phillips head screw driver and 5 minutes of my time. Speaking if the right part.... I would suggest that you remove the 'LATCH-DOOR-NO Handle' from your parts list.It only cause confusion in ordering the part I needed, and a loss of several days time in the repair cycle.
All in all, a good repair experience. I would reccommend you to my " Do It Yourself" friends.
Thanks,
Harold L.

original basket fell apart

  • Customer: D from Villas NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
threw out the broken and put in a fantastically improved new one. very easy (would have done it sooner if I'd known it was that simple to find it online and order it) thanks

The door would just flop down when you opened it

  • Customer: David from Plano TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
The spring mechanism is on the side, so you have to pull the dishwasher out onto the floor. To do that, you have to remove the floor molding (preferably without breaking it) and remove the base coverings (painted metal plates on the bottom of the washer. Unscrew the side gasket plates on the side of the dishwasher (just inside of the door) where it attaches to the cabinet and the screws in the braces at the top (inside the door) where it attaches to the counter top. Now you will be able to slide the washer forward to look at the sides where the door springs are. Depending on the floor, you may have to raise the washer's front feet. They screw up. As you pull the washer forward be careful to not mess up the insulation which drapes over the top and sides. You only need to come out 1/3 of the way to see the sides where there is a plastic wheel at the forward bottom corner. As you move the door up and down you can see the hook where the cable goes and further up the side you can see several notches where the spring goes. Hook the cable and bring it around the wheel and attach it to the spring. To reinstall, just follow these directions backwards. Good luck.

Latch on dishwasher door would not function.

  • Customer: Tammy from Sabetha KS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Simply unscrewed the door and plugged in the new parts. Very quick, very easy, saved us hundreds on a new dishwasher.

panel board would not light up no power

  • Customer: JOHN from HIGHLAND IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Socket set
  • 11 of 28 people found this instruction helpful
removed inside panel,snap new switches in simple but it still dont work

Dishes were coming out dirty... cloudy and white.

  • Customer: Loretta from Ancram NY
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
I know that I have very hard water, but am reluctant to get a softener. I hope that changing the "guts" of the water delivery to my dishwasher will help...already replaced the filters which helped too... so far, it's a little better.

Installation was a breeze. Took off the upper, middle and lower spray arms. Had to loosen screws in filter assembly to remove old manifold. Popped everything into place... had to scrape mineral deposits off clips that support manifold and upper spray arms.
Easy...

door latch loose and door would not open

  • Customer: thomas from gaithersburg MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Had to insert putty knife in the top of latch opening and press up to release the latch so the door would open.

Turn off electric to unit.
Removed the 12 star screws on the panel inside of door.
Pulled out the two wire plugs from the door latch unit, had to use a screwdriver to help push out the metal pronges.
Insert the plugs in the new unit and align the latch pivot point on the door and the two holes with the holes for the inside panel.
Replace the screws.
When the door is closed the latch will be pushed into place and the door is held closed.

Wheel broke on top rack of dishwasher

  • Customer: dr luther c from state college PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench set
  • 3 of 4 people found this instruction helpful
Removed the rack from the dishwasher.
Took off the adjuster from the rack using the allen wrench.
Replaced the new.

Perfect

The spinning wash arm above the glass rack broke off

  • Customer: Cynthia from Van Nuys CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
The part broke off a while ago, and I did not want to call a repair person. The machine still ran, so I ran it with the part missing - the glasses were not very clean, but the repair call was expensive...

I figured that I had a snowballs chance of finding the part number on a molded plastic piece with no numbers printed on it. Boy was I wrong. I was able to choose the part off of a schematic of my machine right on the website and it linked me to the right part order form, so I did not even have to go back and find it on a list.

When the part came, all I had to do was unclip the old mount- with my fingers- no tools, and snap in the new part.

A for maytag for making it easy to fix
A+ for PartSelect for making it so darn easy

Top rack dishes were dirty.

  • Customer: Edward from Springfield VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
Removed assembly holding the docking station to insure the passageway was clear. I reversed the flappers and noticed an improvement in cleaning then decided to order a new part. Installation was simple and the repair seems to have worked well.

Original part was worn out. It would not turn.

  • Customer: Erik from Doral FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 3 of 4 people found this instruction helpful
The original piece is 100% plastic (with metal shields only to prevent burning). The bushing of the arm was badly worn out in one side. The arm was no turning properly or at the end no turning at all. I decide to drill the new part in order to fit a brass bushing inside (1/4" ID, 5/16" OD, about 2" long). I expect it will last considerable longer. I would say this is a typical "defective by design" problem.

Door would not close because latch was not working

  • Customer: Michael P from Greenville TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
I turned off the electricity at the circuit breaker. Sitting in a chair in front of the opened dishwasher with the partially opened door resting on my knees, I removed the 10 screws lining the inside of the door (setting them in order on the cabinet above -- 2 are different length so this helps keep them in order.
I tilted the inner cover on the door up (which is what the screws had been holding). With the door not fully open because it was on my knees, I was able to position the cover so that I did not have to remove the connection to the soap dispenser.
The two middle screws removed earlier were the screws that held the latch in place, so the assembly was already loose at this point. I put a black mark on the assembly to mark the side that the black wires were attached. Then with the pliers removed the plugs that were connected to the switches on either side of the assembly. Then marked the replacement assembly with the black mark on the same side as the one removed. I attached the plugs to the the replacement assembly using the black mark as reminder for which side was which.
I lined up the latch on the door where it goes, lowered the lid (lifting the lower edge over the base a little), lined up and started the latch screws (middle 2), then started all of the other screws and then tightened them all. Closed the lid and tested the latch. It was closing correctly now. I turned on the electricity and tested to make sure all was now working properly.
All Instructions for the ADB2200AWW
76-90 of 478