Models > ADB1500AWW Maytag > Instructions

ADB1500AWW Amana Dishwasher - Instructions

All installation instructions for ADB1500AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ADB1500AWW
46-60 of 342
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dishwasher would not spray water. Water would drain but not spray

  • Customer: Linda from Washington WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
Removed the basketsThen removed the bottom spray arm with nut driver. Removed the cover and spray tower assembly. removed screw holding broken impeller. Replaced and reversed process. Really easy. As an aside. This dishwasher has been a major disappointment. lots of things not holding up. Didn't go cheap when buying it. Nice to find a site with good prices for parts

Water leak from the dishwasher door

  • Customer: Michael from Bronx NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
After replacing the door gasket and seeing that this wasn't the problem, using the schematics found at partselect.com I finally realized that it may be the insulation foam strip. I ordered the product and received it very quickly. Installation went fairly quickly. It was easy to remove the old foam strip and install the new one. The only problem was that the foam strip was about 1/4 " too short and it didn't cover the entire bottom. I improvised a little bit and cut off some of the old strip and covered the gap. So far the leak seems to have been fixed. In addition to the foam strip I had to buy a torx screwdriver for $11 at the local hardware store. The total spent was around $25.

Weeping water control valve

  • Customer: Robert from Woodstock IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 4 of 4 people found this instruction helpful
Turned off water and power to the unit. Removed kick plate from under the dishwasher to access the water contol valve. Placed an absorbant rag under the water valve and water line. Disconnected solenoid on water control valve from electrical connection with my fingers. Used a standard adjustable wrench to disconnect the water line from the water control valve. Then used a 1/4" nut driver to loosen the two bolts that hold the water control valve on to the mounting bracket. Pulled the water control valve slightly forward to disconnect the water feed line to the dishwasher. Used a blunt end plier to pinch the clamp open and slowly wiggle the feed line off of the water control valve. Then removed 90 degree elbow off of the water control valve and used pipe dope and connected the elbow onto the new water control valve. Replaced water control valve in reverse order and utilized new hose clamp to reconnect feed line to new water control valve. Saved door seal for future use, when seal goes bad.

Upper Rack not Cleaning

  • Customer: Stephen J from Sammamish WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
First I read all the reports for not cleaning properly already listed on this site. I had to replace the docking station with flappers. When I removed the station I lost the flappers down the water delivery tube just like Jon said I would in his repair post so I removed the water distribution assembly fished out the old flappers and snapped in the new.
But then I figured I might as well check out the accumulator while I was in the tub anyway - I had read that you need Torx screwdriver bit, which I had, undid the screws, pulled out the accumulator screen which was about 80% clogged, discovered I need a new chopper blade and my impeller is disintegrating, put it back together and lost ten minutes looking for the three screws I had incorrectly put in too soon, and now it is cleaning a packed full load like it was supposed to do.
**I love this site - I went to the virtual repairman and it listed every problem I had with this appliance in the order they happened (door latch broke years ago). - I think I am going to look up stuff that I own so I will know ahead what could go wrong with them.

And absolutely NO DUCT TAPE was used in this repair.

Handle release broke.

  • Customer: Gregory A from Hobbs NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
Take out 12 screws, replace the handle assy, replace the screws in door, done. Took every bit of 10 minutes. I used my power screw-driver with a torx bit.

New house came with dishwasher, but had missing silverware baskets

  • Customer: Mark from Perry OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
Took the baskets out of the packaging and put them in the dishwasher, took about 15 seconds to put both in. They fit perfect, quality factory parts. Thanks PartSelect!

Leaks out and below the front door

  • Customer: John Todd from Franklin WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 5 of 8 people found this instruction helpful
First of all, rather then spending the 44 dollars on the main door seal simply cut yours in halve and trim a quarter of an inch from the disintegrated ends and use superglue and glue these ends together. this glued end will now be up top and in the middle and new clean ends will be down in the corners. next I removed the plastic door panel using a torxhead screwdriver, I just stuck the new inner foam pad on the old one. Then I glued rubber washers to the inner frame about 1/8 thick in the top 2 corners only. Finally I reattached the plastic door being careful not to tighten the torx head bolts just tight enough. It's dry and working good.

drain line had split

  • Customer: William from Interlochen MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 6 of 11 people found this instruction helpful
disconnected unit (electrical, water, and waste) un mounted from countertop, removed from under countertop, unscrewed hose clamb, cut off wire tie. Attached new hose and wire tie (not included) reversed above steps. Done in about 15 minutes

Dishwasher was leaking during wash cycle out the front door

  • Customer: John from Holllis NH
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Replaced the door gasket, inner foam strip and the bottom seals on the door. Unfortunately I broke the plastic door latch handle in the process and had to purchase a complete latch assembly too.

Machine would not fill with water

  • Customer: David from Farmingdale NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 5 of 8 people found this instruction helpful
Remove the 4 screws at the lower panel, turn power off to dishwasher, remove single 1/4 attaching screw from float switch, open the door remove the old float assembly. Make sure you install the float in the machine first than side the switch over the end of the float before screwing it back in.

Dishwasher arm not spinning

  • Customer: Joseph from Warwick RI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench(Adjustable)
  • 4 of 5 people found this instruction helpful
I removed flowplate assembly, chopper assembly, found that the plastic spindle was stripped causing arm not to spin. In the new seal kit, the spindle was made of metal (much better design). I replaced the spindle, chopper, and filter assembly (old one was caked full of gunk). Worked like a charm. A previous post helped me figure out the problem.

If you don't hold door when opening, it will drop down hard

  • Customer: Peter from Westbury NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
First I removed two bottom plates (two screws on each) Then I pulled dishwasher out about six inches. That's as far as it would go because I did not disconnect the water and drain hoses. That was enough to remove the broken cable and collect the disabled spring. I then reattached the new cable to the spring and reworked them into position. NOTE: There is a right and left cable and spring set-up. I used the "good" side as a guide. I then pushed the dishwasher back into place and replaced the two bottom plates.

humidity would seep out absorbing into the granite above

  • Customer: Eric from Overland Park KS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
remove old seal, put in new - my 10 yr old could do it. Note - there is a white mark on the back of the seal indicating the middle so you can line it up when installing the new seal - makes it easier.

Our dishwasher would not take in water. It would partially fill but not to the level required to run properly.

  • Customer: Laurie from Cashton WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
I pulled the dishwasher out from under the countertop. It was quit easy to get to in the lower left front corner of the appliance. I loosened up the bracket that was holding the valve in place. Removed the wires, and taped and ID them so that I would know which one went where. Removed the hose clamp, pulled the hose off and removed the old valve. Put the new one back in just as I removed the old one in the same order. It was a snap! This is not the first time I have used PartSelect! Our evaporate fan went out on our refrigerator a couple years ago, replaced that. A shelf broke in our refrigerator twice, each one different at different times bought both from Part Select. This is the first place I look for help with repairs! I at least attempt to save money, then if it's too difficult I will hire a repairman. So Far, PartSelect has saved me a lot of money on doing it myself! Thanks PartSelect for making small repairs easy to tackle yourself, along with reasonable prices for parts!

Dishwasher wasn't heating the water and dishes were not getting clean.

  • Customer: Victoria from Greenleaf WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
This isn't a how to fix it....it's what part was bad. I had originally contacted the local Maytag repair center and the owner swore up and down that our problem had to be the thermostat and not the heater. He said he had only replaced maybe 5 heaters in 15 years. But our heater looked like heck, with hard water deposits and all, and it wasn't that old, but we went ahead and ordered the thermostat from PartSelect, which came in a day. The problem wasn't the thermostat, so we ordered the heater from PartSelect (again, only one day delivery) and our dishwasher is working again. The heater coil actually had a hole in it from some sort of corrosion. My 18-year-old son did the repair job in a jiffy.
All Instructions for the ADB1500AWW
46-60 of 342