Models > ADB1500AWS10 > Instructions

ADB1500AWS10 Amana Dishwasher - Instructions

All installation instructions for ADB1500AWS10 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ADB1500AWS10
1-15 of 228
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

2 broken wheels on basket

  • Customer: jeanne from waynesboro TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 362 of 364 people found this instruction helpful
unwrapped wheels ,pulled out drawer and easily put on new wheels...as we live way out in the boonies it was great to be able to order parts and have them delivered so fast...easy to fix....

BROKEN WHEELS

  • Customer: Mary J. from Westwood MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 64 of 64 people found this instruction helpful
SNAPPED ON NEW WHEELS

Maytag quiet series 300 stopped cleaning

  • Customer: mike from woodland hills CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 48 of 54 people found this instruction helpful
Remove the racks top and bottom. The Station D seals are at the far back on the tube that supplies water to the top and middle spray heads. Unsnap the old one and snap in the new - it only goes one way! This will repair the seal aroound the tube that supplies the middle sprayer and restore pressure to all 3 heads. Repalcing the screen accumulator is harder. you need a torx driver. remove the little thumb nut on the bottom sprayer and remove the sprayer. Then remove the tube where you just replaced the D station. (You of course could have done this earlier if you were doing both repairs) then 6 screws on the impeller housing. Now remove the 1 torx screw on the impeller and pull the impeller up and off. Remove the 3 screws on the cover and 2 screws on the accumulator. Clean all the old food scraps that are clogging up the works and reassemble in reverse order. Washer is working again!!

Dishwasher not draining completely

  • Customer: Tim from Troy OH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 39 of 41 people found this instruction helpful
You have to pull the dishwasher out from underneath the counter and set it on its side. Before removing, I used a shop vac to remove any standing water from inside the dishwasher. Once I pulled out the dishwasher, I then tilted the dishwasher forward to let remaining water fall on the floor, again, using the wet vac for clean up. After it is on its side, I used a socket wrench to remove the one bolt that holds the drain valve on. Then I used a socket wrench to loosen the clamp for the drain hose and removed the hose. You then need to turn the entire drain valve 1/4 of a turn counter-clockwise to remove the old drain valve. Once it is off, remove the bracket from the old drain and attach it to the new drain valve using a phillips screwdriver. Before I reassambled the drain valve, I used my wet vac to remove any debree from where the drain valve connects to the dishwasher. Reverse the prior steps to install new drain valve and install dishwasher back under the counter. I tested the unit before installing the dishwasher back under the counter to insure it fixed the problem. The hardest part about doing this, was actually taking the dishwasher out from under the counter, very easy process in general. One thing I couldn't figure out about my original problem of the water not completely draining out, is why would the drain valve start draining the water then after 20 seconds it would stop? I couldn't find the answer, so I assumed the drain valve is like a 2 stage system and took a chance on replacing the drain valve; it worked.

Plastic wheel fell off and melted

  • Customer: David from sleepy hollow NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 66 of 127 people found this instruction helpful
Stuck new wheel on, time to find and order part on partselect 2 min, time to open package and install part 1 min.

Total job 3min.

Broken Inlet Valve due to freezing - water leak

  • Customer: Craig from Old Orchard Beach ME
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 35 of 36 people found this instruction helpful
Most of the time was spent pulling out the dishwasher from under the counter, as a new tile floor had been installed after the DW was installed.

Great pictures of components on this website confirmed what part to order.

Shut off water feed to DW and disconnect power to DW.

Unplug wire connector to old valve (solenoid) and disconnect water inlet hose. Observe that valve is attached to sheet metal bracket.

Remove bracket, with valve attached. Don't remove valve from bracket. New valve comes with sheet metal bracket.

Remove female threaded adaptor (brass) from back of old valve and screw on to new valve using Teflon tape. That is the only piece you need to reuse.

Attached the new bracket (with valve attached) to DW. Attach water inlet hose. Attach plug to new valve.

Turn on water to DW. Check for leaks. Retighten hose connection if required. Run dishwasher. Keep lower panel off for a couple of days to be certain no leaks develop.

Wash motor not pumping and making a grinding sound

  • Customer: George from Poughkeepsie NY
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 26 of 31 people found this instruction helpful
I went to PartSelect and found the parts pictorial. A replacement motor was listed for 3 series of the dishwasher. The series can be identified by the first 2 digits of the dishwasher serial number. Mine was 22 so I needed parts for the series 20 dishwasher.

According to the pictorial it looked like the motor seals were included with the replacement motor. When the motor arrived, I found the seals were not included. I called PartSelect and they shipped the seals to me with free overnight delivery.

I had no trouble disassembling the wash manifold and spray parts using the instructions provided with the replacement motor and the instructions from the Maytag repair manual that I found online. The motor is removed from the inside of the tub.... very nice. You don't need to remove the dishwasher from under the counter in order to get at the motor.

I made a mental note of the orientation of the faulty motor before I removed it. I installed the replacement motor with the same orientation along with the wash parts. The dishwasher worked successfully.

Thank you PartSelect.

Dishes were coming out dirty with specs of debris on them

  • Customer: Eric from Newton WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 18 of 21 people found this instruction helpful
I noticed there was a filter type of material in the bottom of the dishwasher that had a small tear in it and figured that was my problem. I removed the nut from the sprayer arm at the bottom of the tub, removed the sprayer arm, removed 3 screws of the plastic cover below that. Removed six screws on the plastic cover below that. Removed one screw fron the center of the black pump spinner wheel that allowed me to lift off that cover. Then I lifted out the flowplate assembly. Placed the new part in and reversed the steps. Works like new again! All for about $30...I am not trianed in any way and have no experience in this kind of thing but am motivated trying to avoid a large service bill for a few screws. I am so happy...Thanks PartSelect!

Dishwasher wouldn't drain.

  • Customer: mark from pearland TN
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 16 of 18 people found this instruction helpful
It was very simple. After disconnecting the dishwasher, I pulled it out from it's space under the cabinet and turned it over on it's side. The pump twists into place and is held by two small bolts. It's very easy to get to and nothing else needs to be taken apart or disconnected. Used some silicon sealant to hold in place after replacing the pump and waited 24 hours to run. The pump was the problem and the dishwasher now runs fine.

Dishwasher wouldn't stay on without pushing on door due to faulty switch.

  • Customer: Andrew from Azusa CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 19 of 30 people found this instruction helpful
Removed plastic lining from dishwasher door with torx screwdriver, then removed screw holding door latch assembly in place. Removed existing switch from door latch assembly and replaced.

This switch was not the correct one initially as it was a normally closed switch, whereas the existing switch was a normally open. Was able to pry open the switch and switch the contacts to normally open so it worked out in the end. Would recommend purchasing the complete latch assembly w/ switches if you aren't comfortable taking the switch apart.

leak in front right corner

  • Customer: Jessica from Lovington IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 15 of 19 people found this instruction helpful
I had to remove the 4 screws holding the toe panel. Then I had to take out the one screw holding the floater switch housing in place. It snapped open to release the floater and that just lifted out. I put the new float in and snapped the new housing on. I put the screw back in to hold the housing in place attached the two wires to the switch and put the toe panel back on. It was all very easy to do and my first home repair went very well. thank you.

Broken handle/latch Dishwasher was very difficult to open.

  • Customer: George from Andover KS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 12 of 13 people found this instruction helpful
The first thing I did was read the all of repair stories that others had submitted. Then I set the timer and chucked up the Torx bit in my electric drill/screwdriver. There are 10 Torx screws on the inside of the dishwasher door and they came out very quickly. The top two screws hold the latch in place. I lifted the inside stainless steel cover to get acces to the latch. There was enough slack in the wire that I was able to remove the latch from where it was and extend it above the door. This let me lay the stainless steel liner back onto the inside of the door without removing or disconnecting the soap dispenser. Thus exposed, disconnecting the connectors from the old latch and reconnecting them to the microswitches on the new latch was a breeze. Once connected, I reinstalled the latch assembly, repositioned the liner correctly and replaced the ten screws. The entire job, including putting my tools away and cleaning up took eight minutes. I did it on my lunch break. The eight minutes included pulling the circuit breaker and reconnecting it (very important, that step). The new latch/handle assembly completely fixed the problem.

grinding noise during cycle

  • Customer: rich from liberty twp OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 11 of 12 people found this instruction helpful
took the bottom spray arm & lower plastic pieces out, unscrewed the impeller & replaced it. the original impeller which holds the disposal blade down & wore down & no longer retained the blade. snap.

A mouse had chewed on the inlet cover to the point that it would no longer stay in it's hole.

  • Customer: Melissa from Wales WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 11 of 15 people found this instruction helpful
Simply popped the new cover in. My part by the way was really easy to identify on the website, easy to order and arrived in a very timley fashion!

broken door springs

  • Customer: jeffrey from holland PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 9 of 12 people found this instruction helpful
I pulled the unit from under the counter. the springs and cables are on the front sides of the dishwasher. I moved the insulation removed the broken spring and cables and replaced them with the new parts. just one side was broken, but I replaced both while I had the unit out.
All Instructions for the ADB1500AWS10
1-15 of 228