Models > AD0252XZ1 > Instructions

AD0252XZ1 Whirlpool Dehumidifier - Instructions

All installation instructions for AD0252XZ1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dehumidifier repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the AD0252XZ1
1-12 of 12
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Refrigerator stop working

  • Customer: SAL from UPLAND CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 13 of 20 people found this instruction helpful
First I removed the relay and over load and exam. Saw that the relay was burnt. Before I order the part I check to see if the compressor was still working by jumping the common start and run terminals.It did. I also checked the start capacitor with a capacitor tester it was good. I than order the part which came the very next day.Installed the part

The compressor did not kick in....

  • Customer: Mike from Sherman CT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 4 of 11 people found this instruction helpful
The repair was easy......however I had no help to identify the problem and after I did I had no description or schematic of how to connect the parts. The old defective part was not identical to the new one. some written material would have been helpful.
Z. Benedek

Cimpressor would not start

  • Customer: Oliver from Madison AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 9 people found this instruction helpful
Checked compressor with amp meter, and found it was not running, found Overload Switch bad.
When removing old switch watch carefully which lug you move wires from, so you will know which
lug to put the new switch on.

BE SURE YOU KNOW SOMETHING ABOUT
ELECTRICITY!!

After Hurricane Irene refrigeration compressore did not start

  • Customer: Bobby from New Bern NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 3 people found this instruction helpful
Followed the directions. Installation was quick. Took loner to put the covers back on and push the applicance back in position than the repair.

change relay

  • Customer: Robert from Boxborough MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 10 people found this instruction helpful
unplugged relay and plugged in

Starting relay went out

  • Customer: George from Conroe TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 13 people found this instruction helpful
Forty years ago I serviced air conditioners and all kinds of refrigeration. At that time starting relays were electro mechanical, I hadn’t looked under a refrigerator in a lot of years and was surprised to find out that the new relays were solid state. The defective one had a bunch of broken pieces floating around in the case. I jury rigged a starting cord and confirmed that the compressor would start and looked at running current for thirty or so seconds. I ordered a new relay kit and it worked just right. I’m seventy five years old and it takes me longer to get up off the floor than it took to replace the parts. Your delivery was first rate the parts got here before I finished doing the paint touch-up on the door under the ice maker/water dispenser. Fed ex was easily three to five days faster than the brown truck.

stopped cooling

  • Customer: bradley from harlingen TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I looked for the obvious sign of malfunction, a leak lack of air flow dirty coil finding nothing obvious I checked the electrical components and the first was the start relay with a bimetal temperature switch was the problem that was identifyed when removed due to the relay sounding like it was internally damaged because of severe rateling

The fridge was blowing how air in the freezer and in the bottom of the fridge.

  • Customer: Katina from Cambridge MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I was careful to unplug each cord one at a time so that I can easily match them up to the new start relay. Once I got the cords plugged into the new start relay, I went ahead and plugged in the fridge and it worked like it never stopped working. I must admit, I'm still nervous about this fridge because I never had to do anything like this in my life so in the back of my mind, I'm always wondering if I did it correctly or not. I was giving a lesson on how to make sure that I have it on correctly but that didn't put me at ease..lol. Parts Select sent this part in less then a day and that made me appreciate there business even more. I was concerned that the part wouldn't get here until later on that week.

The humidifier would run continuously regardless of the humidity setting.

  • Customer: Stephen from Richfield NC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I removed the old humidistat and replaced it with the new one which was an exact fit.

Dehumidifer collection pan (bucket) overflowing with water

  • Customer: Carl from Tuscaloosa AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
The unit should cutoff when the pan gets full enough for it to depress the pan full switch on the back of the unit. Used an ohm-meter to check and see that this switch was bad. Replaced with this part and now it cuts off again when the pan is full. Not hard at all. Take the cover off the unit (screws) then take the switch out (nut) and replace.

freeser and cooler they wasnt work and it won't start

  • Customer: PATRICIO from CHARLOTTE NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
First thing, I didn't have any idea how to fix my refrigerator, but I saw some videos on line, I just pull the start relay, it sound like little parts inside. I order to PART SELECT my Start Relay combination and part select have more comments, diagrams it was easy to find the part. Put the new start relay was easy, I just conect those wires back it took less than 10 minutes and it's working now.thanks to Part Select to make easy to fix it.

compressor clicks on for about 5 seconds and then shuts off, evaporator fan is running but no cooling in the fridge.

  • Customer: Scott from Jay ME
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Disconnect power. Remove back panel on the refrigerator. Relay and overload is a modular unit attached to the compressor. Disconnect module from compressor, install new unit. While you're in there clean the condenser coils with a vacuum and clean the fan and condensate pan. Reassemble, and you're chillin. Total time approx. 15 min.
All Instructions for the AD0252XZ1
1-12 of 12