Models
>
AD0252XW0
AD0252XW0 Whirlpool Dehumidifier - Overview
Sections of the AD0252XW0
[Viewing 3 of 3]
Keep searches simple, eg. "belt" or "pump".
Screw
PartSelect #: PS11742721
Manufacturer #: WP488729
Metallic screw that is less than an inch long. Does not include the plastic washer.
$7.91
In Stock
Hex Nut
PartSelect #: PS11742711
Manufacturer #: WP488130
This hex nut is an authentic Whirlpool part that is sourced directly from the original equipment manufacturer, and will fit a variety of appliances including ovens, microwaves, refrigerators, air cond...
$9.56
In Stock
Single Hex Head Screw
PartSelect #: PS11742731
Manufacturer #: WP489069
Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".
$5.42
In Stock
Screw
PartSelect #: PS11742713
Manufacturer #: WP488234
This screw is sold individually.
Size: 8-32 x 1/4 inch.
$9.13
Special Order
Condensation Drip Pan
PartSelect #: PS401025
Manufacturer #: 951901
Used with dehumidifiers.
No Longer Available
Zip Tie
PartSelect #: PS11753208
Manufacturer #: WPW10339879
A zip tie, also known as a cable tie or a wire tie, is a fastening device that holds wires or tubing together. If a machine has wires or tubing that are easily shifted, you need to hold them tightly t...
$8.04
In Stock
Questions And Answers for AD0252XW0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
old fan motor made horrible screeching sound and siezed up
Removed 4 hex head screws around base of metal housing and 2 screws on bottom front holding on plastic grating and one screw holding housing to switch plate at top front. Hinged grating on back just pops off. Removed two screws holding fan motor on. Unclipped wire terminals (2). Bolted new fan in place.
One hitch was that o ... Read more ne of the little terminal connectors that came with this fan motor was too small, so I had to buy some the right size, and strip the wire and crimp one of those on.
Also, this fan motor is two-speed, and my old dehumidifier is one-speed, so, according to the very helpful instructions, I just taped off one of the wires (not the one I would have guessed--it has you replacing the red with the black and taping off the new red one).
Then reassembled in reverse order, of course.
The only other thing is just that this stinkin' thing was so expensive, but it works fine. It's been humming away for days now, and my basement is once again in the pocket, about 50 - 55% humidity.
And it was pretty easy.
One hitch was that o ... Read more ne of the little terminal connectors that came with this fan motor was too small, so I had to buy some the right size, and strip the wire and crimp one of those on.
Also, this fan motor is two-speed, and my old dehumidifier is one-speed, so, according to the very helpful instructions, I just taped off one of the wires (not the one I would have guessed--it has you replacing the red with the black and taping off the new red one).
Then reassembled in reverse order, of course.
The only other thing is just that this stinkin' thing was so expensive, but it works fine. It's been humming away for days now, and my basement is once again in the pocket, about 50 - 55% humidity.
And it was pretty easy.
Read less
Parts Used:
-
Dave from Roswell, GA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dehumidifier froze up to a solid block of ice
After completely thawing the frozen dehumidifier, I knew the chiller still worked but realized the blower fan did not spin. I ordered a replacement part from PartSelect.com. It arrived in 2 days. With unit unplugged, I removed set knob at the top of the front of the unit, removed two screws at bottom and removed the front grill face ex
... Read more
posing the fan assembly. Next, I unplugged the two fan wires from their connections, removed 4 screws holding fan in place and removed old fan assembly. I then removed the fan blade assembly from old motor by loosing the compression screw and after a thorough cleaning of the fan blades, re-installed it on the new fan motor. The new fan assembly was re-installed with the 4 screws. The fan electrical connections were re-connected. (Note: only the Black and White wires were used as per the original assembly. The Orange wire was left unconnected but bundled with other wires and secured with a tie-wrap.) Dehumidifier was powered up and tested before front grill face was replaced. Mission Complete!
Read less
Parts Used:
-
Robert from Ridley Park, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
5 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dehumidifer collection pan (bucket) overflowing with water
The unit should cutoff when the pan gets full enough for it to depress the pan full switch on the back of the unit. Used an ohm-meter to check and see that this switch was bad. Replaced with this part and now it cuts off again when the pan is full. Not hard at all. Take the cover off the unit (screws) then take the switch out (nut) and re
... Read more
place.
Read less
Parts Used:
-
Carl from Tuscaloosa, AL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!