Models > ACS3350AS > Instructions

ACS3350AS (PACS3350AS0) Amana Range - Instructions

All installation instructions for ACS3350AS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ACS3350AS
181-195 of 200
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Burner wouldn't light. Spark occuring below the burner head between it and the electrode.

  • Customer: Donella from Mount Horeb WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove two phillips screws, lift the burner head up and remove the wire from the electrode. DO NOT DROP THE WIRE!!! It will fall into the stove top, adding much more time and frustration to this very simple repair. Reverse these steps to complete the repair.

No problem

  • Customer: Edward from Somerdale NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I want to praise your customer service. The first parts I received were incorrect by no fault of Parts Select. I called customer service and the assistance I received from "tamarad" was outstanding. She listened to my description of the issue and together figured out the parts originally sent were packaged incorrectly and she walked me through the reordering and in a few days I had the right parts delivered. I wish all customer service experiences were this enjoyable. I will definately use this organization again.

oven would not light

  • Customer: stephen from downers grove IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
after research and diagnosis I determined the igniter to be defective. Even though it glowed red the resistance needed for the "brain" in the oven was too low. This did not let the gas valve open. I removed the floor plate in the oven and removed the screws fastening the igniter. The wire harness plug was in the back of this oven so I fished it out of a hole and unplugged it. I tied a string to the plug(igniter end) and pulled out the unit. fastened the string to the new igniter plug and pulled it out of the back and plugged it in. Reversed the disassembly and ... DONE

SCREWS WERE RUST6ED, MELTED

  • Customer: VICTOR from MOUNT PROSPECT IL
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
USED GRINDER TO CUT THE SCREWS. ALL 4 SCREWS HAD TO BE CUT TO REMOVE FROM BURNER ASSEMBLY. ONCE THIS WAS ACOMPLISED IT WENT FAST WITH NO PROBLEMS

Gas took very long to turn on and failed to reach set temperature

  • Customer: John from Seattle WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Set masonite under feet, removed drawer, and pulled unit out from wall. Disconnected electric and turned off gas supply at wall. Reached in where drawer was and disconnected 2-wire igniter connector. In oven, removed cover in bottom by sliding it off, then undid center bolt on V shaped plate covering igniter and burner. Undid 3 screws holding igniter bracket and pulled through the disconnected wire harness. Removed igniter from bracket carefully as it was held in quite tightly. Carefully slid new igniter in bracket, fed wire in back and replaced 3 screws holding in igniter. Reconnected wire under unit, replaced V plate. Turned on power and gas, tested and gas lit right away. Reassembled the rest and pushed it back against wall.

oven will not heat to temp setting

  • Customer: JOSEPH from RACINE WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
UNPLUG POWER AND TURN OFF GAS VALVE. LOWER DRAWER REMOVED OUT OF WAY.TILT BACK STOVE.LAYED PIECE OF WOOD UNDER FRONT WITH WIFE MAKEING SURE NOT TO FALL FORWARD.REMOVE BACK PLATE(2 SCREWS)YOU WILL SEE THE PLUG IN.UNPLUG.GO INSIDE OF OVEN REMOVE (1SCREW)BOTTOM PLATE.SEE(3SCREWS)REMOVE IGNITER ASSY.PULL OLD OUT,REPLACE NEW ONE (MAY HAVE TO PRY BRACKET APART JUST A BIT TO SLIDE IN).

Lower Bake Ignitor would glow, but would not ignite flame.

  • Customer: Robert from Sapulpa OK
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
First, my wife and I pulled out the oven from wall to disconnect electric plug and, also with a wrench; I shut off the gas connection on the wall. I then removed front door of the oven by pulling up on door to have easy access to lower part of oven, and then removed pan to get to Igniter. Removed the three screws on cage that supported the Igniter and, I also had to remove several screws to the manifold and bottom pan that supports the manifold so that I could disconnect Igniter. I then was able to pull out old Igniter and, reconnect the new one. After that, I reinstalled everything in reverse. Before pushing oven back into wall; we made sure the new igniter worked. It worked just great. My wife and I were so happy and proud that we done it our self, and not have to call someone to do it for us. It took me and, my wife about an hour and a half to complete the job. I believe the reason it took us as long as it did was because we really didn't know what to expect. Now that we know; I am sure that we could do it again in 30 to 45 minutes. Dave & Marsha; 8/23/2013

Oven igniter would not ignite the gas

  • Customer: Robert from Logan UT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
To access the igniter (bake, not broil) I removed the oven racks and removed the pan at the bottom of the oven enclosure (which just lifted out, not secured by any fasteners). Using a Phillips head screw driver, I removed the three small screws that secured the igniter and its shield to the burner. I then pulled out the drawer at the bottom of the oven, looked to the back of the space under the oven, located the igniter connecting plug and disconnected the igniter lead. I was then able to pull the igniter lead wires and plug through the hole at the rear of the oven and remove the igniter from the oven. This can all be done without moving the oven, I just laid on the floor and reached under the oven to disconnect the igniter lead connection. Once the igniter was out of the oven, I carefully removed the igniter from it shield by gently pulling the shield off, there were no fasteners to remove. I installed the new igniter into the existing shield, being careful not to touch or damage the delicate heating element on the igniter. Re-installation of the igniter was just the reverse of the removal process. The whole thing took about 15 minutes for this model of oven, even though I had never replaced an igniter before.

Broiler & burners worked, oven would not ignite or heat up.

  • Customer: Mary from Weston CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Roommate did the repair..so I don't know. I did the research online, the igniter solved the problem. Saved us buying a new oven!

Stove Range Drawer Difficult to Open and Close

  • Customer: Hau from Burke VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Insert one end of the railing into the slot in the back of the stove. Align the front end of the railing with the hole at the front of the stove. Align the roller with the hole. Secure the front end of the railing, roller ,and hole with the shoulder bolt using a 10mm wrench. Tighten just enough but don't over tighten.

When the oven would cycle there were mini explosions and the burner was very noisy. A trouble shooting manual said that this was most likely due to the oven igniter not getting hot enough and gas was accumulating before it finally lit.

  • Customer: Brian from South Talkeetna AK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
1. Remove the oven bottom inside the oven. 2. Remove the pan underneath the oven bottom by undoing one hex nut. 3. Once this is done the oven igniter is visible. It is located in a protective housing. 4. Remove the three sheet metal screws that hold the igniter housing in place. 5. To unplug the igniter remove the storage door. Underneath the oven there is a access panel. Remove it by taking out the two sheet metal screws. Once this is removed the igniter can be unplugged. 6. Pull the old igniter out of the housing and carefully install the new one in it. Careful the ceramic igniter is fragile. 7. Plug the new igniter in and screw the housing back in place. Changing the igniter was easy once we found the panel after removing the storage drawer that made it possible to unplug the old igniter and plug in the new one.

auto door lack stop working

  • Customer: connie from Tallahassee FL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
turn the power off first, remove knobs, removed burners,disconnected wire from igniter,raise the top of the stove,re rmoved wire from the door lock removed two screws remove the door lock itself, then put all back on in same order as I remove. Main thing to remember is to writeyour colors of the wire down so you know where to replace them.

The computer displayed F-2 & F-3 indicating a temp sensor problem.

  • Customer: James from Spotsylvania VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the old sensor which is held into the upper right of the back of the oven by removing the two screws and pulling the sensor out. Then disconnected the sensor from its connector. Replace the old with the new by simply clicking it into the connector. Then pushed the wire back into the oven wall and screwed the two screws back in. The whole job took about one minute to do after evaluating the process. While it was not necessary to remove the door, I did (which was very easy) and ended up cleaning the glass inside and out. All in all, a complete success. Oven working as new.

Would not stop sparking

  • Customer: John from Seattle WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took off the grills and drip pans. Removed the 8 screws, 2 from each burner, which hold on the top. Gently lift burners and pull off electrical contact from each. Lift off and set top aside. Removed knobs on front of oven and screws below each knob. Removed the screws holding the front plate and carefully pry the manifold assembly from the front plate so that the valve shaft is just inside the front plate. Disconnect the old switch and slide off the shaft, then replace with the new switch and reassemble all.

Oven not lighting, sometimes would light, but took a long time.

  • Customer: Jerry from Crystal Falls MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Inside the oven: Pull the bottom floor pan off, just lift up in front and pull back.--Then take the one hex nut off the burner diffuser and lift off.--Remove under storage drawer. On Bottom of oven (Underside): Take off plate in back (2 ea screws) so you can unplug wire to igniter.------Go back inside oven and remove the 3 ea. screws that hold the igniter and holder/guard in place.-----Pull the igniter out.------Replace the new igniter in the holder/guard being careful not to crack the igniter.------Reverse procedure to re-install new unit.
All Instructions for the ACS3350AS
181-195 of 200