Models > ACO1560AS > Instructions

ACO1560AS Amana Microwave - Instructions

All installation instructions for ACO1560AS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ACO1560AS
16-30 of 50
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

latch was on microwave door

  • Customer: william from lithonia GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 8 of 13 people found this instruction helpful
Had to remove door. Next pop off the plastic trim around door. Remove spring holding latch place new latch and afix it to the door frame

Close the door on the microwave, punch in the # nothing happened

  • Customer: Robert S. from Stafford TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 13 people found this instruction helpful
I removed the unit from the wall. Took the cover off. Set the unit on its side. It revealed the working parts. Removed the old micro switches. Put in the new oness. Presto, it worked. Very easy for me.
The parts was delivered almost before my notice they were shipped.

light bulb burned-out

  • Customer: Pablo from Burlingame CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 14 people found this instruction helpful
screwed in new bulb

Fan motor and magnetron did not come on, but every thing else did.

  • Customer: Dale from Chester CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
Problem would come and go. Found service schematic inside unit. Perform all the suggested tests. One possible solution was the primary interlock switch shown on the schematic and a check found the switch stuck. It would free up some times but would stick again in the open position. Ordered switch which was a simple plug in unit.

Needed to push door up to run appliance.

  • Customer: J Patrick from Baltimore MD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 16 people found this instruction helpful
1. Removed cabinet screws (10-15?). 2. Removed cabinet. 3. Removed top interlock switch which actually was not defective. The press clip connection appeared as if it had been arcing for quite some time and the corrosion created resistance sufficient to prevent the current from getting through the switch. 4. Replaced switch anyway but broke plastic retaining clip despite every effort not to do so. Reset broken clip with super glue. 5. Reassembled cabinet and appliance is in good working condition.

Spreader Cover Damaged in fire in oven

  • Customer: Jon from Shafter CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Cleaned area, installed new cover secured with plastic revit.

Plastic latch to lock the microwave door broke.

  • Customer: Richard from Arlington VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 11 people found this instruction helpful
Did an online search for repairs and found PartSelect. Simple to order the part and had it installed myself less than a week later. Thank you!!

BURNT OUT LIGHT BULB REPLACEMENT

  • Customer: alfred from summerville SC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 17 people found this instruction helpful
OPEN COMPARTMENT, INSTALLED BULB, CLOSED COMPARTMENT

turntable erratic and noisy

  • Customer: michael from montgomery TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 5 people found this instruction helpful
Removed 6 screws from bottom cover and 2 from motor cover. Unplugged motor and installed new motor. Plugged in new, Installed cover. Done

Glass Cooking Tray Broke

  • Customer: Mitchell from Henderson NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 5 people found this instruction helpful
Opened Box and Replaced Part......No Problem!

Turn table not turning

  • Customer: Randy from East Peoria IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
My part arrived the next day. That was a surprise to receive it that quick.
I removed the lower panel to gain access to the motor. Disconected the 2 electrical leads and removed the 2 screws that held the motor in position. Installed the new motor, reconnected the leads and reinstalled the lower panel. It was a very easy reapair. I took all of 10 minutes to complete.
I will definately use Parts Select the next time I need a repair part for any appliance.
Great service

turntable stopped working--- unsuccessful so far with the repair

  • Customer: william from Virginia Beach VA
  • Difficulty: Very Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 4 people found this instruction helpful
removed screws from the bottom cover, installed the new motor and reinstalled the cover. The turntable is still not working. wonder if the power supply for that motor is not working. I noticed the internal microwave light glow and then burn out at about the same time as the turn table stopped working. Could that power supply provide power to both the motor and the internal light? can't find the schematics for the location of the power supply so i can test for output power.

burnt out bulb

  • Customer: THOMAS from STOW OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 29 people found this instruction helpful
took cover off, installed bulb.
lost the owners manual,
part select's schematics were very helpful
thanks

Turntable jerking & rumbling noise

  • Customer: George from Hagerstown IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed 7 screws from microwave bottom panel. Panel swings down exposing the turntable motor. Replace motor. Replace the panel. I did not remove the micro wave or the range stove. It is a little difficult working over the stove but it can be done. It does save time. Turntable works o.k. no noise. Doing the job myself saved a $200 service call. On line instructions ,parts list and diagrams are very helpful.

Microwave would not cook

  • Customer: Scott from Mickleton NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
All the electrics worked on Amana microwave EXCEPT for the cooking function. Inspected the control board and found the upper switch on the door interlock was burnt. Installed new switch in minutes and everything now works fine. Unfortunately, had to purchase expensive two switch "kit" although only one switch was kaput. PartsSelect mailing was SUPER fast. Thanks for looking, Scott
All Instructions for the ACO1560AS
16-30 of 50