Models
>
ACF5533AS
ACF5533AS ((MFG.PACF3355AS1)) Maytag Range - Overview
Sections of the ACF5533AS
[Viewing 1 of 1]Keep searches simple, eg. "belt" or "pump".
Spark Ignition Electrode
PartSelect #: PS11757464
Manufacturer #: WPY0316773
This spark ignition electrode lights the gas that starts the burner on your range or cooktop. This electrode is part of the burner assembly, sits next to the burner head, and is just over an inch in l...
$47.20
In Stock
Igniter - Horizontal Mount
PartSelect #: PS11744545
Manufacturer #: WP7432P136-60
This can be used for either the bake igniter or broil igniter in your appliance. NOTE: The part may differ in appearance but will function the same as the original.
$92.32
In Stock
Burner Cap
PartSelect #: PS11745641
Manufacturer #: WP8284669
Burner Cap - 6000 BTU
Sold individually.
$55.11
In Stock
Double Burner Bowl
PartSelect #: PS11740801
Manufacturer #: WP315600B
This black double burner bowl is eighteen inches long and nine and a half inches wide.
No Longer Available
Burner Cap - Matte Black
PartSelect #: PS2033512
Manufacturer #: 31782601MB
The size of this burner cap is actually 2.5" to 2.75 inches in diameter.
No Longer Available
Spark Module
PartSelect #: PS11740990
Manufacturer #: WP31962701
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
No Longer Available
Temperature Sensor
PartSelect #: PS11731155
Manufacturer #: W10850495
This temperature sensor detects the temperature within the oven cavity.
No Longer Available
Questions And Answers for ACF5533AS
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the ACF5533AS
[Viewing 5 of 5]Will Not Start
Fixed by
these parts
these parts
Show All
Little to no heat when baking
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Gas smell
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken Electrode, no spark
Remove 2 screws holding the top burner. Remove 1 screw holding the electrode. Remove electrode from wiring using plier. Install new electrode and top burner
Parts Used:
-
HUY from ALISO VIEJO, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
51 of 61 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The broiler would work but the stove would not lite. I saw the igniter getting to a glow on the broiler and lite but the stove it would not so I figured the igniter might be shot.
1st I opened door to stove and removed the wire racks. Then removed lower panel to get to igniter. Then I had to slide stove away from wall. Remove panel on back for accesss to wires. The new part had a plastic connector and the original just used wire nuts for the connection. So I cut off connector and stripped 1/2 inch of the end. Remov
... Read more
ed wire nuts from old igniter. Back into the oven removed 2 screws pulled out old igniter. Installed new igniter with 2 screws stuck wires through small hole to rear. Back around to back of stove. Connected wires with wire nuts.(I did not see any differnce in wires and dont think it matters) put everything back together and fires that baby up. I am gonna say 15-30 min job
Read less
Parts Used:
-
Robert from plymouth, NH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
49 of 56 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner would not ignite when control in "light" position
Remove the two screws from the burner assembly (on top of the burner). Lift burner assembly from the cook top. Disconnect the electrode wire from the electrode. Remove the screw holding the electrode to the burner assembly (on bottom of burner). Install the new electrode and attach the electrode to the burner assembly. Attach the elec
... Read more
trode wire to the electrode. drop the burner assembly back into position on the cooktop. Attach the burner assembly using two screws.
Read less
Parts Used:
-
Michael from Friendswood, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
22 of 27 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!