Models > ACF4215AB (PACF4215AB0) > Instructions

ACF4215AB (PACF4215AB0) Amana Range - Instructions

All installation instructions for ACF4215AB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ACF4215AB
1-15 of 38
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Baked on sauce

  • Customer: Julie from Newnan GA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 8 of 10 people found this instruction helpful
Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.

The power had gone out and must have sent a surge that fried the ERC. I didn't know that but looked up the "F1" error code that was displayed on the screen online. Once I knew what part to replace it was easy. I just searched out the part on this site and ordered it. I ordered it on a Tuesday

  • Customer: Jeremy from Westmoreland NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 7 people found this instruction helpful
First I unplugged the unit. I removed 4 screws to remove the back plate. Removed 4 screws to remove the ERC unit. ( Plastic casing and all) Peeled the front cover off the old unit and stuck it on the new. Removed one wire at a time and plugged it into the new so I didn't mess up the wiring. screwed my 8 screws back in, plugged it in, and started cooking.

worn hinges, door would not stay closed

  • Customer: Miron from Boise ID
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 7 of 10 people found this instruction helpful
I just got on youtube, typed in "replacing hinges on an amana oven door" and an awesome video popped up. The job was a cinch.

F2 code on display and temperature climbing

  • Customer: Joel from Andover MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 8 people found this instruction helpful
1. Flip "OFF" circuit breaker.
2. Pull out range unit from wall.
3. Unplug range unit.
4. On the back of the range unit, remove 4 screws holding lower rear cover using a phillips head screwdriver.
5. Remove lower rear cover.
6. Unplug temperature sensor connector (1 wire connector located upper right section behind oven).
7. From inside oven (upper left, back corner), remove 2 screws holding temperature sensor unit using a Phillips head screwdriver.
8. Remove old temperature sensor unit.
9. Insert new temperature sensor unit (wire connector end first) through opening and secure reusing old screws.
10. Re-connect temperature sensor connector.
11. Re-attach and secure lower rear cover reusing 4 old screws.
12. Plug in range unit.
13. Move range unit back to desired location.
14. Flip "ON" circuit breaker.

Loose terminal caused block to overheat and break

  • Customer: Dana from Black Mountain NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 8 people found this instruction helpful
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

Replacing the bulb in the freezer side

  • Customer: Yafa (and David) from Bothell WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 4 of 5 people found this instruction helpful
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

No power to the stove

  • Customer: John from Manhattan IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
The repair was easy. I removed the 4 screws to the upper rear cover in the back of oven then unscrewed the 4 screws holding the ERC, Elec Conv-Geneses and undid the 6 color wire conects and the 4 wire plugin. The color wires are labled on diagram and on part. Replaced the divice and reconnected it the same way it in reverse.

However that was not the problem. There was nothing wrong with my ERC, ELEC CONV-GENESIS. I did not check the power to the circuit.
I just figured that it was getting power since the indicator lights were working. One of the 240 circuit
of the circuit breaker was bad (burned out). I turned off the main and replaced the circuit breaker. Works fine now. One learns by there mistakes. Hope this helps...
O by the way I thought I would keep the part just in case I might need it in the future as a backup.

The burner was not heating up

  • Customer: Jeffrey from Miami Lakes FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 6 people found this instruction helpful
I removed only 3 screws that allowed me to lift the glass top on the stove. I removed the burner and I could see where it short circuited. I ordered the new burner element. After it arrived I replaced it by moving the wires from the old element to the new element, and put it back together.
I am sure that I saved at least $200 in "labor".

RIGHT FRONT BURNER ON MY ELETRIC RANGE BURNT OUT.

  • Customer: Glenn from Arlington Heights IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
THE FRONT BURNER THE LARGE ONE WAS BURNT OUT, I COOK ALOT
SO I NEED IT, I HAPPEN TO SEE A APPLIANCE REPAIR MAN NEXT DOOR. I DESCRIBE PROBLEM AND HE SAID WELL FIGURE ABOUT 250 - 300 HUNDRED DOLLARS. 80 FOR THE APRT THE REST LABOR AND HOUSE CALL.WELL I LOOKED AT THE BOOKLET AND FIGURED OUT WHAT I HAD TO DO ,NEEDLESS TO SAY I OWENT TO YOUR WEBSITE AND YOU HAD THE EXACT PART I NEEDED AND SAVED ME ALOT OF MONEY.I SUGEST TO D.I.Yers TRY IT AND IF IT DOESN'T WORK THEN CALL THE REPAIRMAN. THANK YOU PARTS SELECT.
GLENN VOIGHT

cook top was broke

  • Customer: Ed from Bellefontaine OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 9 people found this instruction helpful
we removed the old cook top sixteen screws and four bolts was removed put the new top back on and put all the screws and bolts back in job done

I snapped a bolt on the main power terminal block when connecting the pigtail.

  • Customer: Frank from Palm Coast FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 3 of 4 people found this instruction helpful
Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

Had to replace a rubber whee that was part of one of the drawer slides.

  • Customer: robert from fairport NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
I was surprised when I was able to find that the (10 year old) parts for one of the drawer slides of my stove were still available. However, I was disappointed that the small bolt that I ordered did not come with a nut. I was lucky to find one in a collection of nuts in my workshop, and so was able to fix the slide. However, I suggest that if you supply someone with a bolt, that you include the nut that is necessary to make it work.

drawer wheel completely worn out

  • Customer: Antonina from Stony Brook NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
A Home Depot employee advised me on how to enter all my oven information found on the front of my oven on parts.com. I submitted parts information as stated, also very easy. My parts arrived 3 days later. I used a screwdriver & pliers, it took less than 15 minutes. Very simple and the entire process from order to installation went like clockwork. I would definitely order in the future. Thank you.

burner not turn on

  • Customer: Jorge from Richmond CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 2 people found this instruction helpful
first removed 3 screws in front of the range then lift up the top glass and removed 1 screw that is holding the element and then disconnect the wires that are connect on the element then put the new element on place and wired it test it and works good

electronic control panel fried

  • Customer: cassie from leesport PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 2 people found this instruction helpful
my husband turned off the electric supply, pulled out the stove, took out a couple of screws, put the new part in, and the job was finished
All Instructions for the ACF4215AB
1-15 of 38