Models > ACC4370AW > Instructions

ACC4370AW (PACC4370AW0) Amana Cooktop - Instructions

All installation instructions for ACC4370AW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ACC4370AW
1-10 of 10
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Burner switch failed (full on, even in "lo")

  • Customer: Stephen from Seneca SC
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 11 of 19 people found this instruction helpful
Managed to reach down from the top, unscrew the old part, so I could remove from under the cooktop. Easy to trace the wires, and map them to the (slightly different) replacement. Works like a charm, and new part appears to be of higher quality than the old one.

knob stem broke off switch

  • Customer: TODD from PALOS HEIGHTS IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
I had to remove the 18-22 screws that held in the top of the stove. Then remove the nut that held the switch in place. I took a pictures as I went with my camera phone. That way I remembered which wires went where. Since there was a two day lag getting the part, i was afraid that I would forget. Once I received the part, I just reversed the process. Hardest part was getting the stove top to fit back, as the rubber insulation had expanded a little.

Small burner full hot all the time.

  • Customer: RICHARD from PARADISE TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 6 of 14 people found this instruction helpful
TURNED OFF POWER TO STOVE Removed 5 Knobs, 2 screws that held bad switch.
Removed 4 screws and lifted panel up and forward to expose switches. Adjusted spring tension on knob stem to hold knob ( stem in new switch slightly smaller) removed wire from defective switch one at a time and fastened to new switch in sequence. Reassembled and turned power on. Defective switch had stuck contacts making it full hot.

Both elements were full on and hard to shut off.

  • Customer: RANDY from LA MESA CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Turn the power off. Lifted the stovetop up and rotated it to stand up in the cabinet. Removed the bottom cover and the knob. Put tape markers on all wires for I.D. reference. Disconnected all wires. Identified knob and detent position of the old switch. You could be 180 deg. out. Unscrewed switch assy. from top and removed. Installed new switch assy. after verifying detent position. Using the helpful diagram provided by PartSelect, wires were attached to the new switch. Attach points on the new switch are in different locations than the old switch, at least on my stove. Some wires will need to be re-routed and stretched a bit to fit but it all works. Turned power back on and tested the elements. All fine. Drilled a hole in the bottom cover to attach a clamp to keep the power cable up and out of the way of pots and pans. The original installer neglected to do this. Installed the bottom cover and set the stovetop back in the proper location in the kitchen counter. Had myself a beer for a job well done! The original repair person said the switch would cost $173.00 and was special order. Then he called back and said the part was unavailable. I asked him if he had checked the Internet and he replied that if I wanted to do a search and find something he would be happy to come back and install it. Let's see, $173 plus, maybe an hour install @ $60? per hour versys $58 for the switch and an hour and a half of my time. I think he's still waiting for my call. Thank you PartSelect.

BURNER WOULD,NT HEAT UP.

  • Customer: david from cleveland TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
REMOVED TOP OF STOVE REPLACED HEATING ELEMENT ,PIECE OF CAKE.

Small burner burned out on cooktop.

  • Customer: Kevin from Hurricane WV
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pulled cooktop up on Counter top and unscrewed the screws around around the cook top lifting the glass top off to get to bad burner.then disconnected wires from old burner lifting burner out and sitting new burner down in the cut outs. I have used parts select for my refrigerator,microwave and oven I can't say enough about how great there website is as well as there service.they have made a customer out of me for life and I have turned a lot of friends on to the site and they love it as we'll.

two of the burners went out

  • Customer: george from elk grove CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
the burners were located underneath the glass top, but i had no instructions on how to remove the glass top, so i spent an hour taking every screw off. finally i realized the glass top lifts off from the front then the repair became super easy. hard part was replacing all the screws, lol

bad control switch for stovetop burner

  • Customer: Thomas from Two Harbors MN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Move stove away from wall to allow working on back of stove. Unplug stove. Remove metal cover from top rear of stove. Pull control knob off of control (front of stove) Remove 2 screws holding infinite control in place (front of stove) Replacement control not identical to original control, having more terminal lugs and different physical arrangement. I used the terminal letters as a guide for placement of wires. The letters were not exactly the same, but close enough. Re-attach control to stove with 2 screws. Re-attach back metal panel to stove. Shaft on replacement control is smaller diameter and different shape from original, so I removed ribs from inside of control knob hole and then squirted a small amount of hot glue into the hole. Smearing a small amount of cooking oil onto shaft of replacent control I then slid the control knob onto the control shaft, holding it in place until the glue cooled and set. Plug stove back in, and return stove to its position next to the wall.

Dual right front burner would not modulate temp

  • Customer: Jason from Huntingtown MD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
It is important to remove the two screws holding in the switch first and from the top with a small screwdriver, then remove the wires. Install the wires back on the switch first to assist in holding the relay close to the scew holes. Otherwise much more of the unit needs to be taken apart.

One of the burner wasn't light up.

  • Customer: Sam from Fairport NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The repair was very easy. It took me less than ten minutes. There were only five screws including two to hold heat element that I have to unscrew and transferred the old clip the screw onto new heat element.
All Instructions for the ACC4370AW
1-10 of 10